radix dec ; Code bank 0; Start address: 0; End address: 2047 org 0 ; Define start addresses for data regions shared___globals equ 112 globals___0 equ 32 globals___1 equ 160 globals___2 equ 288 __indf equ 0 __pcl equ 2 __status equ 3 __fsr equ 4 __c___byte equ 3 __c___bit equ 0 __z___byte equ 3 __z___bit equ 2 __rp0___byte equ 3 __rp0___bit equ 5 __rp1___byte equ 3 __rp1___bit equ 6 __irp___byte equ 3 __irp___bit equ 7 __pclath equ 10 __cb0___byte equ 10 __cb0___bit equ 3 __cb1___byte equ 10 __cb1___bit equ 4 ; # Copyright (c) 2005-2008 by Wayne C. Gramlich ; # All rights reserved. ; # This module uses a PIC16F688: ; buffer = 'io8' ; line_number = 7 ; library _pic16f688 entered ; # Copyright (c) 2004-2006 by Wayne C. Gramlich ; # All rights reserved. ; buffer = '_pic16f688' ; line_number = 6 ; processor pic16f688 ; line_number = 7 ; configure_address 0x2007 ; line_number = 8 ; configure_fill 0x3000 ; line_number = 9 ; configure_option fcmen: on = 0x800 ; line_number = 10 ; configure_option fcmen: off = 0x000 ; line_number = 11 ; configure_option ieso: on = 0x400 ; line_number = 12 ; configure_option ieso: off = 0x000 ; line_number = 13 ; configure_option boden: on = 0x300 ; line_number = 14 ; configure_option boden: partial = 0x200 ; line_number = 15 ; configure_option boden: sboden = 0x100 ; line_number = 16 ; configure_option boden: off = 0x000 ; line_number = 17 ; configure_option cpd: on = 0x00 ; line_number = 18 ; configure_option cpd: off = 0x80 ; line_number = 19 ; configure_option cp: on = 0x00 ; line_number = 20 ; configure_option cp: off = 0x40 ; line_number = 21 ; configure_option mclre: on = 0x20 ; line_number = 22 ; configure_option mclre: off = 0x00 ; line_number = 23 ; configure_option pwrte: on = 0x00 ; line_number = 24 ; configure_option pwrte: off = 0x10 ; line_number = 25 ; configure_option wdte: on = 8 ; line_number = 26 ; configure_option wdte: off = 0 ; line_number = 27 ; configure_option fosc: rc_clk = 7 ; line_number = 28 ; configure_option fosc: rc_no_clk = 6 ; line_number = 29 ; configure_option fosc: int_clk = 5 ; line_number = 30 ; configure_option fosc: int_no_clk = 4 ; line_number = 31 ; configure_option fosc: ec = 3 ; line_number = 32 ; configure_option fosc: hs = 2 ; line_number = 33 ; configure_option fosc: xt = 1 ; line_number = 34 ; configure_option fosc: lp = 0 ; line_number = 36 ; code_bank 0x0 : 0x7ff ; line_number = 37 ; code_bank 0x800 : 0xfff ; line_number = 38 ; data_bank 0x0 : 0x7f ; line_number = 39 ; data_bank 0x80 : 0xff ; line_number = 40 ; data_bank 0x100 : 0x17f ; line_number = 41 ; data_bank 0x180 : 0x1ff ; line_number = 43 ; global_region 0x20 : 0x6f ; line_number = 44 ; icd2_global_region 0x20 : 0x6f ; line_number = 46 ; global_region 0xa0 : 0xef ; line_number = 47 ; icd2_global_region 0xa0 : 0xef ; line_number = 49 ; global_region 0x120 : 0x16f ; line_number = 50 ; icd2_global_region 0x120 : 0x164 ; line_number = 52 ; shared_region 0x70 : 0x7f ; line_number = 53 ; icd2_shared_region 0x71 : 0x7f ; line_number = 55 ; interrupts_possible ; line_number = 56 ; packages pdip=14, soic=14, tssop=14 ; line_number = 57 ; pin vdd, power_supply ; line_number = 58 ; pin_bindings pdip=1, soic=1, tssop=1 ; line_number = 59 ; pin ra5_in, ra5_nc, ra5_out, t1cki, osc1, clkin ; line_number = 60 ; pin_bindings pdip=2, soic=2, tssop=2 ; line_number = 61 ; bind_to _porta@5 ; line_number = 62 ; or_if ra5_in _trisa 32 ; line_number = 63 ; or_if ra5_nc _trisa 32 ; line_number = 64 ; or_if ra5_out _trisa 0 ; line_number = 65 ; or_if osc1 _trisa 32 ; line_number = 66 ; pin ra4_in, ra4_nc, ra4_out, t1g, osc2, an3, clkout ; line_number = 67 ; pin_bindings pdip=3, soic=3, tssop=3 ; line_number = 68 ; bind_to _porta@4 ; line_number = 69 ; or_if ra4_in _trisa 16 ; line_number = 70 ; or_if ra4_nc _trisa 16 ; line_number = 71 ; or_if ra4_out _trisa 0 ; line_number = 72 ; or_if an3 _trisa 16 ; line_number = 73 ; or_if osc2 _trisa 16 ; line_number = 74 ; or_if ra4_in _ansel 0 ; line_number = 75 ; or_if ra4_out _ansel 0 ; line_number = 76 ; or_if an3 _ansel 8 ; line_number = 77 ; or_if ra4_in _adcon0 0 ; line_number = 78 ; or_if ra4_out _adcon0 0 ; line_number = 79 ; or_if an3 _adcon0 1 ; line_number = 80 ; pin ra3_in, ra3_nc, mclr, vpp ; line_number = 81 ; pin_bindings pdip=4, soic=4, tssop=4 ; line_number = 82 ; bind_to _porta@3 ; line_number = 83 ; or_if ra3_in _trisa 8 ; line_number = 84 ; or_if ra3_nc _trisa 8 ; line_number = 85 ; pin rc5_in, rc5_nc, rc5_out, rx, dt ; line_number = 86 ; pin_bindings pdip=5, soic=5, tssop=5 ; line_number = 87 ; bind_to _portc@5 ; line_number = 88 ; or_if rc5_in _trisc 32 ; line_number = 89 ; or_if rc5_nc _trisc 32 ; line_number = 90 ; or_if rc5_out _trisc 0 ; line_number = 91 ; or_if rx _trisc 32 ; line_number = 92 ; pin rc4_in, rc4_nc, rc4_out, c2out, tx, ck ; line_number = 93 ; pin_bindings pdip=6, soic=6, tssop=6 ; line_number = 94 ; bind_to _portc@4 ; line_number = 95 ; or_if rc4_in _trisc 16 ; line_number = 96 ; or_if rc4_nc _trisc 16 ; line_number = 97 ; or_if rc4_out _trisc 0 ; # The UART documentation says TX must be marked as in input: ; line_number = 99 ; or_if tx _trisc 16 ; line_number = 100 ; pin rc3_in, rc3_nc, rc3_out, an7 ; line_number = 101 ; pin_bindings pdip=7, soic=7, tssop=7 ; line_number = 102 ; bind_to _portc@3 ; line_number = 103 ; or_if rc3_in _trisc 8 ; line_number = 104 ; or_if rc3_nc _trisc 8 ; line_number = 105 ; or_if rc3_out _trisc 0 ; line_number = 106 ; or_if an7 _trisc 8 ; line_number = 107 ; or_if rc3_in _ansel 0 ; line_number = 108 ; or_if rc3_out _ansel 0 ; line_number = 109 ; or_if an7 _ansel 128 ; line_number = 110 ; or_if rc3_in _adcon0 0 ; line_number = 111 ; or_if rc3_out _adcon0 0 ; line_number = 112 ; or_if an7 _adcon0 1 ; line_number = 113 ; pin rc2_in, rc2_nc, rc2_out, an6 ; line_number = 114 ; pin_bindings pdip=8, soic=8, tssop=8 ; line_number = 115 ; bind_to _portc@2 ; line_number = 116 ; or_if rc2_in _trisc 4 ; line_number = 117 ; or_if rc2_nc _trisc 4 ; line_number = 118 ; or_if rc2_out _trisc 0 ; line_number = 119 ; or_if an6 _trisc 4 ; line_number = 120 ; or_if rc2_in _ansel 0 ; line_number = 121 ; or_if rc2_out _ansel 0 ; line_number = 122 ; or_if an6 _ansel 64 ; line_number = 123 ; or_if rc2_in _adcon0 0 ; line_number = 124 ; or_if rc2_out _adcon0 0 ; line_number = 125 ; or_if an6 _adcon0 1 ; line_number = 126 ; pin rc1_in, rc1_nc, rc1_out, an5, c2in_minus ; line_number = 127 ; pin_bindings pdip=9, soic=9, tssop=9 ; line_number = 128 ; bind_to _portc@1 ; line_number = 129 ; or_if rc1_in _trisc 2 ; line_number = 130 ; or_if rc1_nc _trisc 2 ; line_number = 131 ; or_if rc1_out _trisc 0 ; line_number = 132 ; or_if rc1_in _cmcon0 7 ; line_number = 133 ; or_if rc1_out _cmcon0 7 ; line_number = 134 ; or_if an5 _trisc 2 ; line_number = 135 ; or_if rc1_in _ansel 0 ; line_number = 136 ; or_if rc1_out _ansel 0 ; line_number = 137 ; or_if an5 _ansel 32 ; line_number = 138 ; or_if rc1_in _adcon0 0 ; line_number = 139 ; or_if rc1_out _adcon0 0 ; line_number = 140 ; or_if an5 _adcon0 1 ; line_number = 141 ; pin rc0_in, rc0_nc, rc0_out, an4, c2in_plus ; line_number = 142 ; pin_bindings pdip=10, soic=10, tssop=10 ; line_number = 143 ; bind_to _portc@0 ; line_number = 144 ; or_if rc0_in _trisc 1 ; line_number = 145 ; or_if rc0_nc _trisc 1 ; line_number = 146 ; or_if rc0_out _trisc 0 ; line_number = 147 ; or_if rc0_in _cmcon0 7 ; line_number = 148 ; or_if rc0_out _cmcon0 7 ; line_number = 149 ; or_if an4 _trisc 1 ; line_number = 150 ; or_if rc0_in _ansel 0 ; line_number = 151 ; or_if rc0_out _ansel 0 ; line_number = 152 ; or_if an4 _ansel 16 ; line_number = 153 ; or_if rc0_in _adcon0 0 ; line_number = 154 ; or_if rc0_out _adcon0 0 ; line_number = 155 ; or_if an4 _adcon0 1 ; line_number = 156 ; pin ra2_in, ra2_nc, ra2_out, an2, c1out, t0cki, int ; line_number = 157 ; pin_bindings pdip=11, soic=11, tssop=11 ; line_number = 158 ; bind_to _porta@2 ; line_number = 159 ; or_if ra2_in _trisa 4 ; line_number = 160 ; or_if ra2_nc _trisa 4 ; line_number = 161 ; or_if ra2_out _trisa 0 ; line_number = 162 ; or_if an2 _trisa 4 ; line_number = 163 ; or_if ra2_in _ansel 0 ; line_number = 164 ; or_if ra2_out _ansel 0 ; line_number = 165 ; or_if an2 _ansel 4 ; line_number = 166 ; or_if ra2_in _adcon0 0 ; line_number = 167 ; or_if ra2_out _adcon0 0 ; line_number = 168 ; or_if an2 _adcon0 1 ; line_number = 169 ; pin ra1_in, ra1_nc, ra1_out, an1, c1in_minus, vref, icspclk ; line_number = 170 ; pin_bindings pdip=12, soic=12, tssop=12 ; line_number = 171 ; bind_to _porta@1 ; line_number = 172 ; or_if ra1_in _trisa 2 ; line_number = 173 ; or_if ra1_nc _trisa 2 ; line_number = 174 ; or_if ra1_out _trisa 0 ; line_number = 175 ; or_if ra1_in _cmcon0 7 ; line_number = 176 ; or_if ra1_out _cmcon0 7 ; line_number = 177 ; or_if an1 _trisa 2 ; line_number = 178 ; or_if vref _trisa 2 ; line_number = 179 ; or_if ra1_in _ansel 0 ; line_number = 180 ; or_if ra1_out _ansel 0 ; line_number = 181 ; or_if an1 _ansel 2 ; line_number = 182 ; or_if vref _ansel 2 ; line_number = 183 ; or_if ra1_in _adcon0 0 ; line_number = 184 ; or_if ra1_out _adcon0 0 ; line_number = 185 ; or_if an1 _adcon0 1 # Turn on _addon ; line_number = 186 ; or_if vref _adcon0 1 # Turn on _addon ; line_number = 187 ; or_if vref _adcon0 64 # Turn of _vcfg ; line_number = 188 ; pin ra0_in, ra0_nc, ra0_out, an0, c1in_plus, icspdat, ulpwu ; line_number = 189 ; pin_bindings pdip=13, soic=13, tssop=13 ; line_number = 190 ; bind_to _porta@0 ; line_number = 191 ; or_if ra0_in _trisa 1 ; line_number = 192 ; or_if ra0_nc _trisa 1 ; line_number = 193 ; or_if ra0_out _trisa 0 ; line_number = 194 ; or_if ra0_in _cmcon0 7 ; line_number = 195 ; or_if ra0_out _cmcon0 7 ; line_number = 196 ; or_if an0 _trisa 1 ; line_number = 197 ; or_if ra0_in _ansel 0 ; line_number = 198 ; or_if ra0_out _ansel 0 ; line_number = 199 ; or_if an0 _ansel 1 ; line_number = 200 ; or_if ra0_in _adcon0 0 ; line_number = 201 ; or_if ra0_out _adcon0 0 ; line_number = 202 ; or_if an0 _adcon0 1 ; line_number = 203 ; pin vss, ground ; line_number = 204 ; pin_bindings pdip=14, soic=14, tssop=14 ; line_number = 206 ; library _standard entered ; # Copyright (c) 2006 by Wayne C. Gramlich ; # All rights reserved. ; # Standard definition for uCL: ; buffer = '_standard' ; line_number = 8 ; constant _true = (1 = 1) _true equ 1 ; line_number = 9 ; constant _false = (0 != 0) _false equ 0 ; buffer = '_pic16f688' ; line_number = 206 ; library _standard exited ; # Register/bit bindings: ; # Databank 0 (0x0 - 0x7f): ; line_number = 217 ; register _indf = _indf equ 0 ; line_number = 219 ; register _tmr0 = _tmr0 equ 1 ; line_number = 221 ; register _pcl = _pcl equ 2 ; line_number = 223 ; register _status = _status equ 3 ; line_number = 224 ; bind _irp = _status@7 _irp___byte equ _status _irp___bit equ 7 ; line_number = 225 ; bind _rp1 = _status@5 _rp1___byte equ _status _rp1___bit equ 5 ; line_number = 226 ; bind _rp0 = _status@5 _rp0___byte equ _status _rp0___bit equ 5 ; line_number = 227 ; bind _to = _status@4 _to___byte equ _status _to___bit equ 4 ; line_number = 228 ; bind _pd = _status@3 _pd___byte equ _status _pd___bit equ 3 ; line_number = 229 ; bind _z = _status@2 _z___byte equ _status _z___bit equ 2 ; line_number = 230 ; bind _dc = _status@1 _dc___byte equ _status _dc___bit equ 1 ; line_number = 231 ; bind _c = _status@0 _c___byte equ _status _c___bit equ 0 ; line_number = 233 ; register _fsr = _fsr equ 4 ; line_number = 235 ; register _porta = _porta equ 5 ; line_number = 236 ; register _ra = _ra equ 5 ; line_number = 237 ; bind _ra5 = _porta@5 _ra5___byte equ _porta _ra5___bit equ 5 ; line_number = 238 ; bind _ra4 = _porta@4 _ra4___byte equ _porta _ra4___bit equ 4 ; line_number = 239 ; bind _ra3 = _porta@3 _ra3___byte equ _porta _ra3___bit equ 3 ; line_number = 240 ; bind _ra2 = _porta@2 _ra2___byte equ _porta _ra2___bit equ 2 ; line_number = 241 ; bind _ra1 = _porta@1 _ra1___byte equ _porta _ra1___bit equ 1 ; line_number = 242 ; bind _ra0 = _porta@0 _ra0___byte equ _porta _ra0___bit equ 0 ; line_number = 244 ; register _portc = _portc equ 7 ; line_number = 245 ; register _rc = _rc equ 7 ; line_number = 246 ; bind _rc5 = _portc@5 _rc5___byte equ _portc _rc5___bit equ 5 ; line_number = 247 ; bind _rc4 = _portc@4 _rc4___byte equ _portc _rc4___bit equ 4 ; line_number = 248 ; bind _rc3 = _portc@3 _rc3___byte equ _portc _rc3___bit equ 3 ; line_number = 249 ; bind _rc2 = _portc@2 _rc2___byte equ _portc _rc2___bit equ 2 ; line_number = 250 ; bind _rc1 = _portc@1 _rc1___byte equ _portc _rc1___bit equ 1 ; line_number = 251 ; bind _rc0 = _portc@0 _rc0___byte equ _portc _rc0___bit equ 0 ; line_number = 253 ; register _pclath = _pclath equ 10 ; line_number = 255 ; register _intcon = _intcon equ 11 ; line_number = 256 ; bind _gie = _intcon@7 _gie___byte equ _intcon _gie___bit equ 7 ; line_number = 257 ; bind _peie = _intcon@6 _peie___byte equ _intcon _peie___bit equ 6 ; line_number = 258 ; bind _t0ie = _intcon@5 _t0ie___byte equ _intcon _t0ie___bit equ 5 ; line_number = 259 ; bind _inte = _intcon@4 _inte___byte equ _intcon _inte___bit equ 4 ; line_number = 260 ; bind _raie = _intcon@3 _raie___byte equ _intcon _raie___bit equ 3 ; line_number = 261 ; bind _t0if = _intcon@2 _t0if___byte equ _intcon _t0if___bit equ 2 ; line_number = 262 ; bind _intf = _intcon@1 _intf___byte equ _intcon _intf___bit equ 1 ; line_number = 263 ; bind _raif = _intcon@0 _raif___byte equ _intcon _raif___bit equ 0 ; line_number = 265 ; register _pir1 = _pir1 equ 12 ; line_number = 266 ; bind _eeif = _pir1@7 _eeif___byte equ _pir1 _eeif___bit equ 7 ; line_number = 267 ; bind _adif = _pir1@6 _adif___byte equ _pir1 _adif___bit equ 6 ; line_number = 268 ; bind _rcif = _pir1@5 _rcif___byte equ _pir1 _rcif___bit equ 5 ; line_number = 269 ; bind _c2if = _pir1@4 _c2if___byte equ _pir1 _c2if___bit equ 4 ; line_number = 270 ; bind _c1if = _pir1@3 _c1if___byte equ _pir1 _c1if___bit equ 3 ; line_number = 271 ; bind _osfif = _pir1@2 _osfif___byte equ _pir1 _osfif___bit equ 2 ; line_number = 272 ; bind _txif = _pir1@1 _txif___byte equ _pir1 _txif___bit equ 1 ; line_number = 273 ; bind _tmr1if = _pir1@0 _tmr1if___byte equ _pir1 _tmr1if___bit equ 0 ; line_number = 275 ; register _tmr1l = _tmr1l equ 14 ; line_number = 277 ; register _tmr1h = _tmr1h equ 15 ; line_number = 279 ; register _t1con = _t1con equ 16 ; line_number = 280 ; bind t1ginv = _t1con@7 t1ginv___byte equ _t1con t1ginv___bit equ 7 ; line_number = 281 ; bind _tmr1ge = _t1con@6 _tmr1ge___byte equ _t1con _tmr1ge___bit equ 6 ; line_number = 282 ; bind _t1ckps1 = _t1con@5 _t1ckps1___byte equ _t1con _t1ckps1___bit equ 5 ; line_number = 283 ; bind _t1ckps0 = _t1con@4 _t1ckps0___byte equ _t1con _t1ckps0___bit equ 4 ; line_number = 284 ; bind _t1oscen = _t1con@3 _t1oscen___byte equ _t1con _t1oscen___bit equ 3 ; line_number = 285 ; bind _t1sync = _t1con@2 _t1sync___byte equ _t1con _t1sync___bit equ 2 ; line_number = 286 ; bind _tmr1cs = _t1con@1 _tmr1cs___byte equ _t1con _tmr1cs___bit equ 1 ; line_number = 287 ; bind _tmr1on = _t1con@0 _tmr1on___byte equ _t1con _tmr1on___bit equ 0 ; line_number = 289 ; register _baudctl = _baudctl equ 17 ; line_number = 290 ; bind _abdovf = _baudctl@7 _abdovf___byte equ _baudctl _abdovf___bit equ 7 ; line_number = 291 ; bind _rcidl = _baudctl@6 _rcidl___byte equ _baudctl _rcidl___bit equ 6 ; line_number = 292 ; bind _sckp = _baudctl@4 _sckp___byte equ _baudctl _sckp___bit equ 4 ; line_number = 293 ; bind _brg16 = _baudctl@3 _brg16___byte equ _baudctl _brg16___bit equ 3 ; line_number = 294 ; bind _wue = _baudctl@1 _wue___byte equ _baudctl _wue___bit equ 1 ; line_number = 295 ; bind _abden = _baudctl@0 _abden___byte equ _baudctl _abden___bit equ 0 ; line_number = 297 ; register _spbrgh = _spbrgh equ 18 ; line_number = 299 ; register _spbrg = _spbrg equ 19 ; line_number = 301 ; register _rcreg = _rcreg equ 20 ; line_number = 303 ; register _txreg = _txreg equ 21 ; line_number = 305 ; register _txsta = _txsta equ 22 ; line_number = 306 ; bind _csrc = _txsta@7 _csrc___byte equ _txsta _csrc___bit equ 7 ; line_number = 307 ; bind _tx9 = _txsta@6 _tx9___byte equ _txsta _tx9___bit equ 6 ; line_number = 308 ; bind _txen = _txsta@5 _txen___byte equ _txsta _txen___bit equ 5 ; line_number = 309 ; bind _sync = _txsta@4 _sync___byte equ _txsta _sync___bit equ 4 ; line_number = 310 ; bind _sendb = _txsta@3 _sendb___byte equ _txsta _sendb___bit equ 3 ; line_number = 311 ; bind _brgh = _txsta@2 _brgh___byte equ _txsta _brgh___bit equ 2 ; line_number = 312 ; bind _trmt = _txsta@1 _trmt___byte equ _txsta _trmt___bit equ 1 ; line_number = 313 ; bind _tx9d = _txsta@0 _tx9d___byte equ _txsta _tx9d___bit equ 0 ; line_number = 315 ; register _rcsta = _rcsta equ 23 ; line_number = 316 ; bind _spen = _rcsta@7 _spen___byte equ _rcsta _spen___bit equ 7 ; line_number = 317 ; bind _rx9 = _rcsta@6 _rx9___byte equ _rcsta _rx9___bit equ 6 ; line_number = 318 ; bind _sren = _rcsta@5 _sren___byte equ _rcsta _sren___bit equ 5 ; line_number = 319 ; bind _cren = _rcsta@4 _cren___byte equ _rcsta _cren___bit equ 4 ; line_number = 320 ; bind _adden = _rcsta@3 _adden___byte equ _rcsta _adden___bit equ 3 ; line_number = 321 ; bind _ferr = _rcsta@2 _ferr___byte equ _rcsta _ferr___bit equ 2 ; line_number = 322 ; bind _oerr = _rcsta@1 _oerr___byte equ _rcsta _oerr___bit equ 1 ; line_number = 323 ; bind _rx9d = _rcsta@0 _rx9d___byte equ _rcsta _rx9d___bit equ 0 ; line_number = 325 ; register _wdtcon = _wdtcon equ 24 ; line_number = 326 ; bind _wdtps3 = _wdtcon@4 _wdtps3___byte equ _wdtcon _wdtps3___bit equ 4 ; line_number = 327 ; bind _wdtps2 = _wdtcon@3 _wdtps2___byte equ _wdtcon _wdtps2___bit equ 3 ; line_number = 328 ; bind _wdtps1 = _wdtcon@2 _wdtps1___byte equ _wdtcon _wdtps1___bit equ 2 ; line_number = 329 ; bind _wdtps0 = _wdtcon@1 _wdtps0___byte equ _wdtcon _wdtps0___bit equ 1 ; line_number = 330 ; bind _swdten = _wdtcon@0 _swdten___byte equ _wdtcon _swdten___bit equ 0 ; line_number = 332 ; register _cmcon0 = _cmcon0 equ 25 ; line_number = 333 ; bind _c1out = _cmcon0@7 _c1out___byte equ _cmcon0 _c1out___bit equ 7 ; line_number = 334 ; bind _c2out = _cmcon0@6 _c2out___byte equ _cmcon0 _c2out___bit equ 6 ; line_number = 335 ; bind _c1inv = _cmcon0@5 _c1inv___byte equ _cmcon0 _c1inv___bit equ 5 ; line_number = 336 ; bind _c2inv = _cmcon0@4 _c2inv___byte equ _cmcon0 _c2inv___bit equ 4 ; line_number = 337 ; bind _cis = _cmcon0@3 _cis___byte equ _cmcon0 _cis___bit equ 3 ; line_number = 338 ; bind _cm2 = _cmcon0@2 _cm2___byte equ _cmcon0 _cm2___bit equ 2 ; line_number = 339 ; bind _cm1 = _cmcon0@1 _cm1___byte equ _cmcon0 _cm1___bit equ 1 ; line_number = 340 ; bind _cm0 = _cmcon0@0 _cm0___byte equ _cmcon0 _cm0___bit equ 0 ; line_number = 342 ; register _cmcon1 = _cmcon1 equ 26 ; line_number = 343 ; bind _t1gss = _cmcon1@0 _t1gss___byte equ _cmcon1 _t1gss___bit equ 0 ; line_number = 344 ; bind _c2sync = _cmcon1@1 _c2sync___byte equ _cmcon1 _c2sync___bit equ 1 ; line_number = 346 ; register _adresh = _adresh equ 30 ; line_number = 348 ; register _adcon0 = _adcon0 equ 31 ; line_number = 349 ; bind _adfm = _adcon0@7 _adfm___byte equ _adcon0 _adfm___bit equ 7 ; line_number = 350 ; bind _vcfg = _adcon0@6 _vcfg___byte equ _adcon0 _vcfg___bit equ 6 ; line_number = 351 ; bind _chs2 = _adcon0@4 _chs2___byte equ _adcon0 _chs2___bit equ 4 ; line_number = 352 ; bind _chs1 = _adcon0@3 _chs1___byte equ _adcon0 _chs1___bit equ 3 ; line_number = 353 ; bind _chs0 = _adcon0@2 _chs0___byte equ _adcon0 _chs0___bit equ 2 ; line_number = 354 ; bind _go = _adcon0@1 _go___byte equ _adcon0 _go___bit equ 1 ; line_number = 355 ; bind _adon = _adcon0@0 _adon___byte equ _adcon0 _adon___bit equ 0 ; # Data bank 1 (0x80-0xff): ; line_number = 359 ; register _option_reg = _option_reg equ 129 ; line_number = 360 ; bind _rapu = _option_reg@7 _rapu___byte equ _option_reg _rapu___bit equ 7 ; line_number = 361 ; bind _intedg = _option_reg@6 _intedg___byte equ _option_reg _intedg___bit equ 6 ; line_number = 362 ; bind _t0cs = _option_reg@5 _t0cs___byte equ _option_reg _t0cs___bit equ 5 ; line_number = 363 ; bind _t0se = _option_reg@4 _t0se___byte equ _option_reg _t0se___bit equ 4 ; line_number = 364 ; bind _psa = _option_reg@3 _psa___byte equ _option_reg _psa___bit equ 3 ; line_number = 365 ; bind _ps2 = _option_reg@2 _ps2___byte equ _option_reg _ps2___bit equ 2 ; line_number = 366 ; bind _ps1 = _option_reg@1 _ps1___byte equ _option_reg _ps1___bit equ 1 ; line_number = 367 ; bind _ps0 = _option_reg@0 _ps0___byte equ _option_reg _ps0___bit equ 0 ; line_number = 369 ; register _trisa = _trisa equ 133 ; line_number = 370 ; bind _trisa5 = _trisa@5 _trisa5___byte equ _trisa _trisa5___bit equ 5 ; line_number = 371 ; bind _trisa4 = _trisa@4 _trisa4___byte equ _trisa _trisa4___bit equ 4 ; line_number = 372 ; bind _trisa3 = _trisa@3 _trisa3___byte equ _trisa _trisa3___bit equ 3 ; line_number = 373 ; bind _trisa2 = _trisa@2 _trisa2___byte equ _trisa _trisa2___bit equ 2 ; line_number = 374 ; bind _trisa1 = _trisa@1 _trisa1___byte equ _trisa _trisa1___bit equ 1 ; line_number = 375 ; bind _trisa0 = _trisa@0 _trisa0___byte equ _trisa _trisa0___bit equ 0 ; line_number = 377 ; register _trisc = _trisc equ 135 ; line_number = 378 ; bind _trisc5 = _trisc@5 _trisc5___byte equ _trisc _trisc5___bit equ 5 ; line_number = 379 ; bind _trisc4 = _trisc@4 _trisc4___byte equ _trisc _trisc4___bit equ 4 ; line_number = 380 ; bind _trisc3 = _trisc@3 _trisc3___byte equ _trisc _trisc3___bit equ 3 ; line_number = 381 ; bind _trisc2 = _trisc@2 _trisc2___byte equ _trisc _trisc2___bit equ 2 ; line_number = 382 ; bind _trisc1 = _trisc@1 _trisc1___byte equ _trisc _trisc1___bit equ 1 ; line_number = 383 ; bind _trisc0 = _trisc@0 _trisc0___byte equ _trisc _trisc0___bit equ 0 ; line_number = 385 ; register _pie1 = _pie1 equ 140 ; line_number = 386 ; bind _eeie = _pie1@7 _eeie___byte equ _pie1 _eeie___bit equ 7 ; line_number = 387 ; bind _adie = _pie1@6 _adie___byte equ _pie1 _adie___bit equ 6 ; line_number = 388 ; bind _rcie = _pie1@5 _rcie___byte equ _pie1 _rcie___bit equ 5 ; line_number = 389 ; bind _c2ie = _pie1@4 _c2ie___byte equ _pie1 _c2ie___bit equ 4 ; line_number = 390 ; bind _c1ie = _pie1@3 _c1ie___byte equ _pie1 _c1ie___bit equ 3 ; line_number = 391 ; bind _osfie = _pie1@2 _osfie___byte equ _pie1 _osfie___bit equ 2 ; line_number = 392 ; bind _txie = _pie1@1 _txie___byte equ _pie1 _txie___bit equ 1 ; line_number = 393 ; bind _tmr1ie = _pie1@0 _tmr1ie___byte equ _pie1 _tmr1ie___bit equ 0 ; line_number = 395 ; register _pcon = _pcon equ 142 ; line_number = 396 ; bind _ulpwue = _pcon@5 _ulpwue___byte equ _pcon _ulpwue___bit equ 5 ; line_number = 397 ; bind _sboden = _pcon@4 _sboden___byte equ _pcon _sboden___bit equ 4 ; line_number = 398 ; bind _por = _pcon@1 _por___byte equ _pcon _por___bit equ 1 ; line_number = 399 ; bind _bod = _pcon@0 _bod___byte equ _pcon _bod___bit equ 0 ; line_number = 401 ; register _osccon = _osccon equ 143 ; line_number = 402 ; bind _ircf2 = _osccon@6 _ircf2___byte equ _osccon _ircf2___bit equ 6 ; line_number = 403 ; bind _ircf1 = _osccon@5 _ircf1___byte equ _osccon _ircf1___bit equ 5 ; line_number = 404 ; bind _ircf0 = _osccon@4 _ircf0___byte equ _osccon _ircf0___bit equ 4 ; line_number = 405 ; bind _osts = _osccon@3 _osts___byte equ _osccon _osts___bit equ 3 ; line_number = 406 ; bind _hts = _osccon@2 _hts___byte equ _osccon _hts___bit equ 2 ; line_number = 407 ; bind _lts = _osccon@3 _lts___byte equ _osccon _lts___bit equ 3 ; line_number = 408 ; bind _scs = _osccon@2 _scs___byte equ _osccon _scs___bit equ 2 ; line_number = 410 ; register _osctune = _osctune equ 144 ; line_number = 411 ; bind _tun4 = _osctune@4 _tun4___byte equ _osctune _tun4___bit equ 4 ; line_number = 412 ; bind _tun3 = _osctune@3 _tun3___byte equ _osctune _tun3___bit equ 3 ; line_number = 413 ; bind _tun2 = _osctune@2 _tun2___byte equ _osctune _tun2___bit equ 2 ; line_number = 414 ; bind _tun1 = _osctune@1 _tun1___byte equ _osctune _tun1___bit equ 1 ; line_number = 415 ; bind _tun0 = _osctune@0 _tun0___byte equ _osctune _tun0___bit equ 0 ; line_number = 416 ; constant _osccal_lsb = 1 _osccal_lsb equ 1 ; line_number = 418 ; register _ansel = _ansel equ 145 ; line_number = 419 ; bind _ans7 = _ansel@7 _ans7___byte equ _ansel _ans7___bit equ 7 ; line_number = 420 ; bind _ans6 = _ansel@6 _ans6___byte equ _ansel _ans6___bit equ 6 ; line_number = 421 ; bind _ans5 = _ansel@5 _ans5___byte equ _ansel _ans5___bit equ 5 ; line_number = 422 ; bind _ans4 = _ansel@4 _ans4___byte equ _ansel _ans4___bit equ 4 ; line_number = 423 ; bind _ans3 = _ansel@3 _ans3___byte equ _ansel _ans3___bit equ 3 ; line_number = 424 ; bind _ans2 = _ansel@2 _ans2___byte equ _ansel _ans2___bit equ 2 ; line_number = 425 ; bind _ans1 = _ansel@1 _ans1___byte equ _ansel _ans1___bit equ 1 ; line_number = 426 ; bind _ans0 = _ansel@0 _ans0___byte equ _ansel _ans0___bit equ 0 ; line_number = 428 ; register _wpua = _wpua equ 149 ; line_number = 429 ; bind _wpua5 = _wpua@5 _wpua5___byte equ _wpua _wpua5___bit equ 5 ; line_number = 430 ; bind _wpua4 = _wpua@4 _wpua4___byte equ _wpua _wpua4___bit equ 4 ; line_number = 431 ; bind _wpua2 = _wpua@2 _wpua2___byte equ _wpua _wpua2___bit equ 2 ; line_number = 432 ; bind _wpua1 = _wpua@1 _wpua1___byte equ _wpua _wpua1___bit equ 1 ; line_number = 433 ; bind _wpua0 = _wpua@0 _wpua0___byte equ _wpua _wpua0___bit equ 0 ; line_number = 435 ; register _ioca = _ioca equ 150 ; line_number = 436 ; bind _ioca5 = _ioca@5 _ioca5___byte equ _ioca _ioca5___bit equ 5 ; line_number = 437 ; bind _ioca4 = _ioca@4 _ioca4___byte equ _ioca _ioca4___bit equ 4 ; line_number = 438 ; bind _ioca3 = _ioca@3 _ioca3___byte equ _ioca _ioca3___bit equ 3 ; line_number = 439 ; bind _ioca2 = _ioca@2 _ioca2___byte equ _ioca _ioca2___bit equ 2 ; line_number = 440 ; bind _ioca1 = _ioca@1 _ioca1___byte equ _ioca _ioca1___bit equ 1 ; line_number = 441 ; bind _ioca0 = _ioca@0 _ioca0___byte equ _ioca _ioca0___bit equ 0 ; line_number = 443 ; register _eedath = _eedath equ 151 ; line_number = 445 ; register _eeadrh = _eeadrh equ 152 ; line_number = 447 ; register _vrcon = _vrcon equ 153 ; line_number = 448 ; bind _vren = _vrcon@7 _vren___byte equ _vrcon _vren___bit equ 7 ; line_number = 449 ; bind _vrr = _vrcon@5 _vrr___byte equ _vrcon _vrr___bit equ 5 ; line_number = 450 ; bind _vr3 = _vrcon@3 _vr3___byte equ _vrcon _vr3___bit equ 3 ; line_number = 451 ; bind _vr2 = _vrcon@2 _vr2___byte equ _vrcon _vr2___bit equ 2 ; line_number = 452 ; bind _vr1 = _vrcon@1 _vr1___byte equ _vrcon _vr1___bit equ 1 ; line_number = 453 ; bind _vr0 = _vrcon@0 _vr0___byte equ _vrcon _vr0___bit equ 0 ; line_number = 455 ; register _eedat = _eedat equ 154 ; line_number = 456 ; bind _eedat7 = _eedat@7 _eedat7___byte equ _eedat _eedat7___bit equ 7 ; line_number = 457 ; bind _eedat6 = _eedat@6 _eedat6___byte equ _eedat _eedat6___bit equ 6 ; line_number = 458 ; bind _eedat5 = _eedat@5 _eedat5___byte equ _eedat _eedat5___bit equ 5 ; line_number = 459 ; bind _eedat4 = _eedat@4 _eedat4___byte equ _eedat _eedat4___bit equ 4 ; line_number = 460 ; bind _eedat3 = _eedat@3 _eedat3___byte equ _eedat _eedat3___bit equ 3 ; line_number = 461 ; bind _eedat2 = _eedat@2 _eedat2___byte equ _eedat _eedat2___bit equ 2 ; line_number = 462 ; bind _eedat1 = _eedat@1 _eedat1___byte equ _eedat _eedat1___bit equ 1 ; line_number = 463 ; bind _eedat0 = _eedat@0 _eedat0___byte equ _eedat _eedat0___bit equ 0 ; line_number = 465 ; register _eeadr = _eeadr equ 155 ; line_number = 466 ; bind _eeadr7 = _eeadr@7 _eeadr7___byte equ _eeadr _eeadr7___bit equ 7 ; line_number = 467 ; bind _eeadr6 = _eeadr@6 _eeadr6___byte equ _eeadr _eeadr6___bit equ 6 ; line_number = 468 ; bind _eeadr5 = _eeadr@5 _eeadr5___byte equ _eeadr _eeadr5___bit equ 5 ; line_number = 469 ; bind _eeadr4 = _eeadr@4 _eeadr4___byte equ _eeadr _eeadr4___bit equ 4 ; line_number = 470 ; bind _eeadr3 = _eeadr@3 _eeadr3___byte equ _eeadr _eeadr3___bit equ 3 ; line_number = 471 ; bind _eeadr2 = _eeadr@2 _eeadr2___byte equ _eeadr _eeadr2___bit equ 2 ; line_number = 472 ; bind _eeadr1 = _eeadr@1 _eeadr1___byte equ _eeadr _eeadr1___bit equ 1 ; line_number = 473 ; bind _eeadr0 = _eeadr@0 _eeadr0___byte equ _eeadr _eeadr0___bit equ 0 ; line_number = 475 ; register _eecon1 = _eecon1 equ 156 ; line_number = 476 ; bind _eepgd = _eecon1@7 _eepgd___byte equ _eecon1 _eepgd___bit equ 7 ; line_number = 477 ; bind _wrerr = _eecon1@3 _wrerr___byte equ _eecon1 _wrerr___bit equ 3 ; line_number = 478 ; bind _wren = _eecon1@2 _wren___byte equ _eecon1 _wren___bit equ 2 ; line_number = 479 ; bind _wr = _eecon1@1 _wr___byte equ _eecon1 _wr___bit equ 1 ; line_number = 480 ; bind _rd = _eecon1@0 _rd___byte equ _eecon1 _rd___bit equ 0 ; line_number = 482 ; register _eecon2 = _eecon2 equ 157 ; line_number = 484 ; register _adresl = _adresl equ 158 ; line_number = 486 ; register _adcon1 = _adcon1 equ 159 ; line_number = 487 ; bind _adcs2 = _adcon1@6 _adcs2___byte equ _adcon1 _adcs2___bit equ 6 ; line_number = 488 ; bind _adcs1 = _adcon1@5 _adcs1___byte equ _adcon1 _adcs1___bit equ 5 ; line_number = 489 ; bind _adcs0 = _adcon1@4 _adcs0___byte equ _adcon1 _adcs0___bit equ 4 ; # Data Bank 2 (0x100 - 0x17f): ; buffer = 'io8' ; line_number = 7 ; library _pic16f688 exited ; # The system is running at 20MHz: ; line_number = 10 ; library clock20mhz entered ; # Copyright (c) 2004 by Wayne C. Gramlich ; # All rights reserved. ; # This library defines the contstants {clock_rate}, {instruction_rate}, ; # and {clocks_per_instruction}. ; # Define processor constants: ; buffer = 'clock20mhz' ; line_number = 9 ; constant clock_rate = 20000000 clock_rate equ 20000000 ; line_number = 10 ; constant clocks_per_instruction = 4 clocks_per_instruction equ 4 ; line_number = 11 ; constant instruction_rate = clock_rate / clocks_per_instruction instruction_rate equ 5000000 ; buffer = 'io8' ; line_number = 10 ; library clock20mhz exited ; # A microsecond takes 5 cycles at 20MHz: ; line_number = 12 ; constant microsecond = 5 microsecond equ 5 ; # The {_eusart} library defines some baud rate generator constants: ; line_number = 15 ; constant _eusart_clock = clock_rate _eusart_clock equ 20000000 ; line_number = 16 ; constant _eusart_factor = 4 _eusart_factor equ 4 ; line_number = 17 ; library _eusart entered ; # Copyright (c) 2005 by Wayne C. Gramlich ; # All rights reserved. ; # This library contains a bunch of definitions for the Enhanced Universal ; # Asynchronous Serial Receiver/Transmitter (EUSART) that is available ; # on many of the PIC microcontrollers. ; # In order to use this module you have to get two constants defined ; # BEFORE including this library -- {_eusart_factor} and {_eusart_clock}. ; # {_eusart_clock} should be set to the frequency oscillator for the chip. ; # {_eusart_factor} should be set to 4, 16, or 64 depending upon whether ; # the {_brg16} and {_brgh} bits are set. Use the table below to select: ; # ; # _{brg16} {_brgh} _{eusart_factor} ; # 0 0 64 ; # 0 1 16 ; # 1 0 16 ; # 1 1 4 ; # 2400 bits/sec: ; buffer = '_eusart' ; line_number = 23 ; constant _eusart_2400 = (_eusart_clock / (2400 * _eusart_factor)) - 1 _eusart_2400 equ 2082 ; line_number = 24 ; constant _eusart_2400_low = _eusart_2400 & 0xff _eusart_2400_low equ 34 ; line_number = 25 ; constant _eusart_2400_high = _eusart_2400 >> 8 _eusart_2400_high equ 8 ; line_number = 26 ; constant _eusart_2400_index = 0 _eusart_2400_index equ 0 ; # 4800 bits/sec: ; line_number = 28 ; constant _eusart_4800 = (_eusart_clock / (4800 * _eusart_factor)) - 1 _eusart_4800 equ 1040 ; line_number = 29 ; constant _eusart_4800_low = _eusart_4800 & 0xff _eusart_4800_low equ 16 ; line_number = 30 ; constant _eusart_4800_high = _eusart_4800 >> 8 _eusart_4800_high equ 4 ; line_number = 31 ; constant _eusart_4800_index = 1 _eusart_4800_index equ 1 ; # 9600 bits/sec: ; line_number = 33 ; constant _eusart_9600 = (_eusart_clock / (9600 * _eusart_factor)) - 1 _eusart_9600 equ 519 ; line_number = 34 ; constant _eusart_9600_low = _eusart_9600 & 0xff _eusart_9600_low equ 7 ; line_number = 35 ; constant _eusart_9600_high = _eusart_9600 >> 8 _eusart_9600_high equ 2 ; line_number = 36 ; constant _eusart_9600_index = 2 _eusart_9600_index equ 2 ; # 19200 bits/sec: ; line_number = 38 ; constant _eusart_19200 = (_eusart_clock / (19200 * _eusart_factor)) - 1 _eusart_19200 equ 259 ; line_number = 39 ; constant _eusart_19200_low = _eusart_19200 & 0xff _eusart_19200_low equ 3 ; line_number = 40 ; constant _eusart_19200_high = _eusart_19200 >> 8 _eusart_19200_high equ 1 ; line_number = 41 ; constant _eusart_19200_index = 3 _eusart_19200_index equ 3 ; # 38400 bits/sec: ; line_number = 43 ; constant _eusart_38400 = (_eusart_clock / (38400 * _eusart_factor)) - 1 _eusart_38400 equ 129 ; line_number = 44 ; constant _eusart_38400_low = _eusart_38400 & 0xff _eusart_38400_low equ 129 ; line_number = 45 ; constant _eusart_38400_high = _eusart_38400 >> 8 _eusart_38400_high equ 0 ; line_number = 46 ; constant _eusart_38400_index = 4 _eusart_38400_index equ 4 ; # 57600 bits/sec: ; line_number = 48 ; constant _eusart_57600 = (_eusart_clock / (57600 * _eusart_factor)) - 1 _eusart_57600 equ 85 ; line_number = 49 ; constant _eusart_57600_low = _eusart_57600 & 0xff _eusart_57600_low equ 85 ; line_number = 50 ; constant _eusart_57600_high = _eusart_57600 >> 8 _eusart_57600_high equ 0 ; line_number = 51 ; constant _eusart_57600_index = 5 _eusart_57600_index equ 5 ; # 115200 bits/sec: ; line_number = 53 ; constant _eusart_115200 = (_eusart_clock / (115200 * _eusart_factor)) - 1 _eusart_115200 equ 42 ; line_number = 54 ; constant _eusart_115200_low = _eusart_115200 & 0xff _eusart_115200_low equ 42 ; line_number = 55 ; constant _eusart_115200_high = _eusart_115200 >> 8 _eusart_115200_high equ 0 ; line_number = 56 ; constant _eusart_115200_index = 6 _eusart_115200_index equ 6 ; # 203400 bits/sec: ; line_number = 58 ; constant _eusart_230400 = (_eusart_clock / (230400 * _eusart_factor)) - 1 _eusart_230400 equ 20 ; line_number = 59 ; constant _eusart_230400_low = _eusart_230400 & 0xff _eusart_230400_low equ 20 ; line_number = 60 ; constant _eusart_230400_high = _eusart_230400 >> 8 _eusart_230400_high equ 0 ; line_number = 61 ; constant _eusart_230400_index = 7 _eusart_230400_index equ 7 ; # 406800 bits/sec: ; line_number = 63 ; constant _eusart_460800 = (_eusart_clock / (460800 * _eusart_factor)) - 1 _eusart_460800 equ 9 ; line_number = 64 ; constant _eusart_460800_low = _eusart_460800 & 0xff _eusart_460800_low equ 9 ; line_number = 65 ; constant _eusart_460800_high = _eusart_460800 >> 8 _eusart_460800_high equ 0 ; line_number = 66 ; constant _eusart_460800_index = 8 _eusart_460800_index equ 8 ; # 500000 bits/sec: ; line_number = 68 ; constant _eusart_500000 = (_eusart_clock / (500000 * _eusart_factor)) - 1 _eusart_500000 equ 9 ; line_number = 69 ; constant _eusart_500000_low = _eusart_500000 & 0xff _eusart_500000_low equ 9 ; line_number = 70 ; constant _eusart_500000_high = _eusart_500000 >> 8 _eusart_500000_high equ 0 ; line_number = 71 ; constant _eusart_500000_index = 9 _eusart_500000_index equ 9 ; # 576000 bits/sec (1MHz): ; line_number = 73 ; constant _eusart_576000 = (_eusart_clock / (576000 * _eusart_factor)) - 1 _eusart_576000 equ 7 ; line_number = 74 ; constant _eusart_576000_low = _eusart_576000 & 0xff _eusart_576000_low equ 7 ; line_number = 75 ; constant _eusart_576000_high = _eusart_576000 >> 8 _eusart_576000_high equ 0 ; line_number = 76 ; constant _eusart_576000_index = 10 _eusart_576000_index equ 10 ; # 625000 bits/sec: ; line_number = 78 ; constant _eusart_625000 = (_eusart_clock / (625000 * _eusart_factor)) - 1 _eusart_625000 equ 7 ; line_number = 79 ; constant _eusart_625000_low = _eusart_625000 & 0xff _eusart_625000_low equ 7 ; line_number = 80 ; constant _eusart_625000_high = _eusart_625000 >> 8 _eusart_625000_high equ 0 ; line_number = 81 ; constant _eusart_625000_index = 11 _eusart_625000_index equ 11 ; # 833333 bits/sec: ; line_number = 83 ; constant _eusart_833333 = (_eusart_clock / (833333 * _eusart_factor)) - 1 _eusart_833333 equ 5 ; line_number = 84 ; constant _eusart_833333_low = _eusart_833333 & 0xff _eusart_833333_low equ 5 ; line_number = 85 ; constant _eusart_833333_high = _eusart_833333 >> 8 _eusart_833333_high equ 0 ; line_number = 86 ; constant _eusart_833333_index = 12 _eusart_833333_index equ 12 ; # 921600 bits/sec: ; line_number = 88 ; constant _eusart_921600 = (_eusart_clock / (921600 * _eusart_factor)) - 1 _eusart_921600 equ 4 ; line_number = 89 ; constant _eusart_921600_low = _eusart_921600 & 0xff _eusart_921600_low equ 4 ; line_number = 90 ; constant _eusart_921600_high = _eusart_921600 >> 8 _eusart_921600_high equ 0 ; line_number = 91 ; constant _eusart_921600_index = 13 _eusart_921600_index equ 13 ; # 1000000 bits/sec (1MHz): ; line_number = 93 ; constant _eusart_1000000 = (_eusart_clock / (1000000 * _eusart_factor)) - 1 _eusart_1000000 equ 4 ; line_number = 94 ; constant _eusart_1000000_low = _eusart_1000000 & 0xff _eusart_1000000_low equ 4 ; line_number = 95 ; constant _eusart_1000000_high = _eusart_1000000 >> 8 _eusart_1000000_high equ 0 ; line_number = 96 ; constant _eusart_1000000_index = 14 _eusart_1000000_index equ 14 ; buffer = 'io8' ; line_number = 17 ; library _eusart exited ; # The library of bus access routines for use by a PIC16F688. ; line_number = 20 ; library rb2bus_pic16f688 entered ; # Copyright (c) 2006 by Wayne C. Gramlich ; # All rights reserved. ; # This module provides some procedures for accessing a RoboBricks2 ; # bus via a UART. It is speicialized for the PIC16F688. ; # ; # It defines the following procedure: ; # ; # {rb2bus_initialize}({address}) The procedure that initializes the UART ; # for bus access. ; # All other bus access procedures are defined in the {rb2bus} library ; # which is accessed below: ; buffer = 'rb2bus_pic16f688' ; line_number = 16 ; library rb2bus entered ; # Copyright (c) 2006-2007 by Wayne C. Gramlich ; # All rights reserved. ; # This module provides some procedures for accessing a RoboBricks2 ; # bus via a UART. ; # ; # This procedure defines the following procedures: ; # ; # {rb2bus_select_wait} This procedure waits for the module to become selected ; # {rb2bus_deselect} This procedure causes this module to be deselected. ; # {rb2bus_byte_get} This procedure will get a byte form the bus. ; # {rb2bus_byte_put} This procedure will send a byte to the bus. ; # ; # The global variable {rb2bus_error} is set to 1 whenever the procedures ; # feel like there is a command decoding error. ; # ; # The way to use these procedures is quite as follows: ; # ; # # Comamnd byte variable: ; # local command byte ; # ; # # Other initialize code goes here: ; # ; # # Process commands from bus master: ; # loop_forever ; # rb2bus_error := _true ; # while rb2bus_error ; # call rb2bus_select_wait() ; # command := rb2bus_byte_get() ; # ; # # Decode command: ; # switch command >> 6 ; # ... ; # case 5: ; # # 0000 0101 (Foo command): ; # if !rb2bus_error ; # # Do foo command: ; # ; # The key concept behind these procedures is to make command ; # decoding for the slave module easy. If the slave module ; # is in the middle of command decoding and the master suddenly ; # sends out a module select command, we need to gracefully recover ; # from the problem. A command should only be executed if ; # {rb2bus_error} is not set. If {rb2bus_error} is set, we want ; # to gracefully get back to the beginning of the loop without ; # doing any damage. Once {rb2bus_error} is set, all calls to ; # {rb2bus_byte_get} return 0 and all calls to {rb2bus_byte_put} ; # do nothing. At the beginning of the loop, {rb2bus_error} is ; # cleared by the {rb2bus_select_wait}() procedure and we have ; # recovered from the situation. ; buffer = 'rb2bus' ; line_number = 54 ; library rb2_constants entered ; # Copyright (c) 2006-2007 by Wayne C. Gramlich. ; # All rights reserved. ; buffer = 'rb2_constants' ; line_number = 6 ; constant rb2_ok = 0xa5 rb2_ok equ 165 ; line_number = 8 ; constant rb2_common_address_set = 0xfc rb2_common_address_set equ 252 ; line_number = 9 ; constant rb2_common_id_next = 0xfd rb2_common_id_next equ 253 ; line_number = 10 ; constant rb2_common_id_start = 0xfe rb2_common_id_start equ 254 ; line_number = 11 ; constant rb2_common_deselect = 0xff rb2_common_deselect equ 255 ; line_number = 13 ; constant rb2_laser1_address = 1 rb2_laser1_address equ 1 ; line_number = 14 ; constant rb2_laser1_sense_read = 0 rb2_laser1_sense_read equ 0 ; line_number = 15 ; constant rb2_laser1_enable_read = 1 rb2_laser1_enable_read equ 1 ; line_number = 16 ; constant rb2_laser1_enable_clear = 2 rb2_laser1_enable_clear equ 2 ; line_number = 17 ; constant rb2_laser1_enable_set = 3 rb2_laser1_enable_set equ 3 ; line_number = 19 ; constant rb2_minimotor2_address = 2 rb2_minimotor2_address equ 2 ; line_number = 20 ; constant rb2_midimotor2_address = 3 rb2_midimotor2_address equ 3 ; line_number = 21 ; constant rb2_motor0_speed_get = 0 rb2_motor0_speed_get equ 0 ; line_number = 22 ; constant rb2_motor0_speed_set = 1 rb2_motor0_speed_set equ 1 ; line_number = 23 ; constant rb2_motor1_speed_get = 2 rb2_motor1_speed_get equ 2 ; line_number = 24 ; constant rb2_motor1_speed_set = 3 rb2_motor1_speed_set equ 3 ; line_number = 25 ; constant rb2_duty_cycle_get = 4 rb2_duty_cycle_get equ 4 ; line_number = 26 ; constant rb2_duty_cycle_set = 8 rb2_duty_cycle_set equ 8 ; line_number = 28 ; constant rb2_irdistance2_address = 4 rb2_irdistance2_address equ 4 ; line_number = 29 ; constant rb2_irdistance2_raw0_get = 0 rb2_irdistance2_raw0_get equ 0 ; line_number = 30 ; constant rb2_irdistance2_raw1_get = 1 rb2_irdistance2_raw1_get equ 1 ; line_number = 31 ; constant rb2_irdistance2_smooth0_get = 2 rb2_irdistance2_smooth0_get equ 2 ; line_number = 32 ; constant rb2_irdistance2_smooth1_get = 3 rb2_irdistance2_smooth1_get equ 3 ; line_number = 33 ; constant rb2_irdistance2_linear0_get = 4 rb2_irdistance2_linear0_get equ 4 ; line_number = 34 ; constant rb2_irdistance2_linear1_get = 6 rb2_irdistance2_linear1_get equ 6 ; line_number = 36 ; constant rb2_shaft2_address = 5 rb2_shaft2_address equ 5 ; line_number = 37 ; constant rb2_shaft2_count_latch = 0 rb2_shaft2_count_latch equ 0 ; line_number = 38 ; constant rb2_shaft2_count_clear = 1 rb2_shaft2_count_clear equ 1 ; line_number = 39 ; constant rb2_shaft2_shaft0_high_get = 2 rb2_shaft2_shaft0_high_get equ 2 ; line_number = 40 ; constant rb2_shaft2_shaft1_high_get = 3 rb2_shaft2_shaft1_high_get equ 3 ; line_number = 41 ; constant rb2_shaft2_continue_get = 4 rb2_shaft2_continue_get equ 4 ; line_number = 42 ; constant rb2_shaft2_shaft0_low_get = rb2_shaft2_continue_get rb2_shaft2_shaft0_low_get equ 4 ; line_number = 43 ; constant rb2_shaft2_shaft1_low_get = rb2_shaft2_continue_get rb2_shaft2_shaft1_low_get equ 4 ; line_number = 44 ; constant rb2_shaft2_x_get = 0x10 rb2_shaft2_x_get equ 16 ; line_number = 45 ; constant rb2_shaft2_y_get = 0x11 rb2_shaft2_y_get equ 17 ; line_number = 46 ; constant rb2_shaft2_bearing16_get = 0x12 rb2_shaft2_bearing16_get equ 18 ; line_number = 47 ; constant rb2_shaft2_bearing8_get = 0x13 rb2_shaft2_bearing8_get equ 19 ; line_number = 48 ; constant rb2_shaft2_target_x_get = 0x14 rb2_shaft2_target_x_get equ 20 ; line_number = 49 ; constant rb2_shaft2_target_y_get = 0x15 rb2_shaft2_target_y_get equ 21 ; line_number = 50 ; constant rb2_shaft2_target_bearing16_get = 0x16 rb2_shaft2_target_bearing16_get equ 22 ; line_number = 51 ; constant rb2_shaft2_target_bearing8_get = 0x17 rb2_shaft2_target_bearing8_get equ 23 ; line_number = 52 ; constant rb2_shaft2_target_distance_get = 0x18 rb2_shaft2_target_distance_get equ 24 ; line_number = 53 ; constant rb2_shaft2_wheel_spacing_get = 0x19 rb2_shaft2_wheel_spacing_get equ 25 ; line_number = 54 ; constant rb2_shaft2_wheel_ticks_get = 0x1a rb2_shaft2_wheel_ticks_get equ 26 ; line_number = 55 ; constant rb2_shaft2_wheel_diameter_get = 0x1b rb2_shaft2_wheel_diameter_get equ 27 ; line_number = 56 ; constant rb2_shaft2_count_iteration_get = 0x1c rb2_shaft2_count_iteration_get equ 28 ; line_number = 57 ; constant rb2_shaft2_counter_signs_get = 0x1d rb2_shaft2_counter_signs_get equ 29 ; line_number = 58 ; constant rb2_shaft2_x_set = 0x20 rb2_shaft2_x_set equ 32 ; line_number = 59 ; constant rb2_shaft2_y_set = 0x21 rb2_shaft2_y_set equ 33 ; line_number = 60 ; constant rb2_shaft2_bearing16_set = 0x22 rb2_shaft2_bearing16_set equ 34 ; line_number = 61 ; constant rb2_shaft2_navigation_latch = 0x23 rb2_shaft2_navigation_latch equ 35 ; line_number = 62 ; constant rb2_shaft2_target_x_set = 0x24 rb2_shaft2_target_x_set equ 36 ; line_number = 63 ; constant rb2_shaft2_target_y_set = 0x25 rb2_shaft2_target_y_set equ 37 ; line_number = 64 ; constant rb2_shaft2_wheel_spacing_set = 0x29 rb2_shaft2_wheel_spacing_set equ 41 ; line_number = 65 ; constant rb2_shaft2_wheel_ticks_set = 0x2a rb2_shaft2_wheel_ticks_set equ 42 ; line_number = 66 ; constant rb2_shaft2_wheel_diameter_set = 0x2b rb2_shaft2_wheel_diameter_set equ 43 ; line_number = 67 ; constant rb2_shaft2_counter_signs_set = 0x2c rb2_shaft2_counter_signs_set equ 44 ; line_number = 69 ; constant rb2_orient5_address = 6 rb2_orient5_address equ 6 ; line_number = 71 ; constant rb2_compass8_address = 7 rb2_compass8_address equ 7 ; line_number = 73 ; constant rb2_io8_address = 8 rb2_io8_address equ 8 ; line_number = 74 ; constant rb2_io8_digital8_get = 0 rb2_io8_digital8_get equ 0 ; line_number = 75 ; constant rb2_io8_digital8_set = 1 rb2_io8_digital8_set equ 1 ; line_number = 76 ; constant rb2_io8_direction_get = 2 rb2_io8_direction_get equ 2 ; line_number = 77 ; constant rb2_io8_direction_set = 3 rb2_io8_direction_set equ 3 ; line_number = 78 ; constant rb2_io8_analog_mask_get = 4 rb2_io8_analog_mask_get equ 4 ; line_number = 79 ; constant rb2_io8_analog_mask_set = 5 rb2_io8_analog_mask_set equ 5 ; line_number = 80 ; constant rb2_io8_analog8_get = 0x10 rb2_io8_analog8_get equ 16 ; line_number = 81 ; constant rb2_io8_analog10_get = 0x18 rb2_io8_analog10_get equ 24 ; line_number = 82 ; constant rb2_low_set = 0x20 rb2_low_set equ 32 ; line_number = 83 ; constant rb2_high_set = 0x30 rb2_high_set equ 48 ; line_number = 85 ; constant rb2_sonar2_address = 9 rb2_sonar2_address equ 9 ; line_number = 87 ; constant rb2_voice1_address = 10 rb2_voice1_address equ 10 ; line_number = 89 ; constant rb2_servo4_address = 11 rb2_servo4_address equ 11 ; line_number = 90 ; constant rb2_servo4_servo0 = 0 rb2_servo4_servo0 equ 0 ; line_number = 91 ; constant rb2_servo4_servo1 = 1 rb2_servo4_servo1 equ 1 ; line_number = 92 ; constant rb2_servo4_servo2 = 2 rb2_servo4_servo2 equ 2 ; line_number = 93 ; constant rb2_servo4_servo3 = 3 rb2_servo4_servo3 equ 3 ; line_number = 94 ; constant rb2_servo4_quick_set = 0 rb2_servo4_quick_set equ 0 ; line_number = 95 ; constant rb2_servo4_quick_low = 0 rb2_servo4_quick_low equ 0 ; line_number = 96 ; constant rb2_servo4_quick_center = 40 rb2_servo4_quick_center equ 40 ; line_number = 97 ; constant rb2_servo4_quick_high = 0x7c rb2_servo4_quick_high equ 124 ; line_number = 98 ; constant rb2_servo4_high_low_set = 0x80 rb2_servo4_high_low_set equ 128 ; line_number = 99 ; constant rb2_servo4_short_high_low_set = 0x84 rb2_servo4_short_high_low_set equ 132 ; line_number = 100 ; constant rb2_servo4_high_set = 0x88 rb2_servo4_high_set equ 136 ; line_number = 101 ; constant rb2_servo4_low_set = 0x8c rb2_servo4_low_set equ 140 ; line_number = 102 ; constant rb2_servo4_enables_set = 0x90 rb2_servo4_enables_set equ 144 ; line_number = 103 ; constant rb2_servo4_enable0 = 1 rb2_servo4_enable0 equ 1 ; line_number = 104 ; constant rb2_servo4_enable1 = 2 rb2_servo4_enable1 equ 2 ; line_number = 105 ; constant rb2_servo4_enable2 = 4 rb2_servo4_enable2 equ 4 ; line_number = 106 ; constant rb2_servo4_enable3 = 8 rb2_servo4_enable3 equ 8 ; line_number = 107 ; constant rb2_servo4_enable_all = 0xf rb2_servo4_enable_all equ 15 ; line_number = 108 ; constant rb2_servo4_enable_none = 0 rb2_servo4_enable_none equ 0 ; line_number = 109 ; constant rb2_servo4_high_get = 0xa0 rb2_servo4_high_get equ 160 ; line_number = 110 ; constant rb2_servo4_low_get = 0xa4 rb2_servo4_low_get equ 164 ; line_number = 111 ; constant rb2_servo4_enables_get = 0xa8 rb2_servo4_enables_get equ 168 ; line_number = 113 ; constant rb2_controller28_address = 28 rb2_controller28_address equ 28 ; line_number = 115 ; constant rb2_lcd32_address = 32 rb2_lcd32_address equ 32 ; line_number = 116 ; constant rb2_lcd32_row_set = 4 rb2_lcd32_row_set equ 4 ; line_number = 117 ; constant rb2_lcd32_row0_set = rb2_lcd32_row_set | 0 rb2_lcd32_row0_set equ 4 ; line_number = 118 ; constant rb2_lcd32_row1_set = rb2_lcd32_row_set | 1 rb2_lcd32_row1_set equ 5 ; line_number = 119 ; constant rb2_lcd32_row2_set = rb2_lcd32_row_set | 2 rb2_lcd32_row2_set equ 6 ; line_number = 120 ; constant rb2_lcd32_row3_set = rb2_lcd32_row_set | 3 rb2_lcd32_row3_set equ 7 ; line_number = 121 ; constant rb2_lcd32_new_line = 0xa rb2_lcd32_new_line equ 10 ; line_number = 122 ; constant rb2_lcd32_form_feed = 0xc rb2_lcd32_form_feed equ 12 ; line_number = 123 ; constant rb2_lcd32_carriage_return = 0xd rb2_lcd32_carriage_return equ 13 ; line_number = 124 ; constant rb2_lcd32_column_set = 0x10 rb2_lcd32_column_set equ 16 ; buffer = 'rb2bus' ; line_number = 54 ; library rb2_constants exited ; line_number = 55 ; library rb2bus_globals entered ; # Copyright (c) 2006-2007 by Wayne C. Gramlich ; # All rights reserved. ; # These are the global variables used by both the {rb2bus} and ; # the various {rb2bus_picXXXX} libraries. Poll based firmware ; # uses both libraries, whereas interrupt driven software only ; # uses the {rb2bus_picXXX} libraries. ; buffer = 'rb2bus_globals' ; line_number = 11 ; global rb2bus_selected bit # rb2bus_selected___byte equ globals___0+79 rb2bus_selected___bit equ 0 ; line_number = 12 ; global rb2bus_error bit # Global error bit rb2bus_error___byte equ globals___0+79 rb2bus_error___bit equ 1 ; line_number = 13 ; global rb2bus_address byte # Bus address to respond to rb2bus_address equ globals___0 ; line_number = 14 ; global rb2bus_index byte # Index into id information rb2bus_index equ globals___0+1 ; buffer = 'rb2bus' ; line_number = 55 ; library rb2bus_globals exited ; Delaying code generation for procedure rb2bus_select_wait ; Delaying code generation for procedure rb2bus_deselect ; Delaying code generation for procedure rb2bus_byte_get ; Delaying code generation for procedure rb2bus_byte_put ; Delaying code generation for procedure rb2bus_command ; buffer = 'rb2bus_pic16f688' ; line_number = 16 ; library rb2bus exited ; Delaying code generation for procedure rb2bus_initialize ; line_number = 62 ; constant rb2bus_eedata_address = 0xfe rb2bus_eedata_address equ 254 ; Delaying code generation for procedure rb2bus_eedata_read ; Delaying code generation for procedure rb2bus_eedata_write ; buffer = 'io8' ; line_number = 20 ; library rb2bus_pic16f688 exited ; # This module uses 20MHz crystal oscillator; hence mode EC=External Clock: ; # All pins on this package are used except RA3. ; line_number = 26 ; package pdip ; line_number = 27 ; pin 1 = power_supply ; line_number = 28 ; pin 2 = osc1 ; line_number = 29 ; pin 3 = ra4_in, name=io5, mask=io5_mask, bit=io5_bit io5___byte equ _porta io5___bit equ 4 io5_mask equ 16 io5_bit equ 4 ; line_number = 30 ; pin 4 = ra3_nc, name=nc1 nc1___byte equ _porta nc1___bit equ 3 ; line_number = 31 ; pin 5 = rx, name=rx, bit=rx_bit rx___byte equ _portc rx___bit equ 5 rx_bit equ 5 ; line_number = 32 ; pin 6 = tx, name=tx, bit=tx_bit tx___byte equ _portc tx___bit equ 4 tx_bit equ 4 ; line_number = 33 ; pin 7 = rc3_in, name=io1, mask=io1_mask, bit=io1_bit io1___byte equ _portc io1___bit equ 3 io1_mask equ 8 io1_bit equ 3 ; line_number = 34 ; pin 8 = rc2_in, name=io2, mask=io2_mask, bit=io2_bit io2___byte equ _portc io2___bit equ 2 io2_mask equ 4 io2_bit equ 2 ; line_number = 35 ; pin 9 = rc1_in, name=io0, mask=io0_mask, bit=io0_bit io0___byte equ _portc io0___bit equ 1 io0_mask equ 2 io0_bit equ 1 ; line_number = 36 ; pin 10 = rc0_in, name=io3, mask=io3_mask, bit=io3_bit io3___byte equ _portc io3___bit equ 0 io3_mask equ 1 io3_bit equ 0 ; line_number = 37 ; pin 11 = ra2_in, name=io7, mask=io7_mask, bit=io7_bit io7___byte equ _porta io7___bit equ 2 io7_mask equ 4 io7_bit equ 2 ; line_number = 38 ; pin 12 = ra1_in, name=io4, mask=io4_mask, bit=io4_bit io4___byte equ _porta io4___bit equ 1 io4_mask equ 2 io4_bit equ 1 ; line_number = 39 ; pin 13 = ra0_in, name=io6, mask=io6_mask, bit=io6_bit io6___byte equ _porta io6___bit equ 0 io6_mask equ 1 io6_bit equ 0 ; line_number = 40 ; pin 14 = ground ; line_number = 42 ; global adc_lsbs[8] array[byte] adc_lsbs equ globals___0+12 ; line_number = 43 ; global adc_msbs[8] array[byte] adc_msbs equ globals___0+20 ; line_number = 45 ; origin 0 org 0 ; #procedure start ; # arguments_none ; # returns_nothing ; # return_suppress ; # ; # assemble ; # codebank start, main ; # goto main ; # ; #origin 4 ; line_number = 58 ; global time_high bit time_high___byte equ globals___0+79 time_high___bit equ 4 ; line_number = 59 ; global pulse_low byte pulse_low equ globals___0+28 ; line_number = 60 ; global pulse_high byte pulse_high equ globals___0+29 ; line_number = 61 ; global pulse_count byte pulse_count equ globals___0+30 ; line_number = 62 ; global analog_threshold byte analog_threshold equ globals___0+31 ; #procedure interrupt ; # arguments_none ; # returns_nothing ; # ; # local a byte ; # ; # # No matter what, turn the counter off: ; # _tmr1on := _false ; # ; # # Make sure it is the register A interrupt flag: ; # if _raif ; # # We need to read port A to clear the condition. Doing a ; # # bit test does not read port A and (hence) does not clear ; # # the condition: ; # a := _porta ; # _raif := _false ; # ; # # Bump pulse counter: ; # pulse_count := pulse_count + 1 ; # ; # # IO7 bit changed; turn the counter on and off: ; # if time_high ; # # Measure the length of a high pulse: ; # if !(a@io7_bit) ; # # We just went low; record the result: ; # pulse_low := _tmr1l ; # pulse_high := _tmr1h ; # else ; # # Measure the length of a low pulse: ; # if a@io7_bit ; # # We just went high; record the resulta: ; # pulse_low := _tmr1l ; # pulse_high := _tmr1h ; # ; # # Zero the counter and turn it on: ; # _tmr1h := 0 ; # _tmr1l := 0 ; # _tmr1on := _true ; line_number = 104 ;info 104, 0 ; procedure main main: ; Initialize some registers clrf _adcon0 bsf __rp0___byte, __rp0___bit clrf _ansel movlw 7 bcf __rp0___byte, __rp0___bit movwf _cmcon0 movlw 63 bsf __rp0___byte, __rp0___bit movwf _trisa movlw 63 movwf _trisc ; arguments_none ; line_number = 106 ; returns_nothing ; # This procedure initializes everything and does command decoding. ; line_number = 111 ; local command byte main__command equ globals___0+32 ; line_number = 112 ; local channel byte main__channel equ globals___0+33 ; line_number = 113 ; local high byte main__high equ globals___0+34 ; line_number = 114 ; local low byte main__low equ globals___0+35 ; line_number = 115 ; local result byte main__result equ globals___0+36 ; line_number = 116 ; local mask byte main__mask equ globals___0+37 ; line_number = 117 ; local mask_complement byte main__mask_complement equ globals___0+38 ; line_number = 118 ; local temporary byte main__temporary equ globals___0+39 ; # For now keep interrupts off: ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>01 code:X0=cu=>X0) ; line_number = 121 ; _gie := _false ;info 121, 11 bcf _gie___byte, _gie___bit ; line_number = 123 ; call rb2bus_initialize(8) ;info 123, 12 movlw 8 bcf __rp0___byte, __rp0___bit call rb2bus_initialize ; line_number = 125 ; call direction_set(0xff) ;info 125, 15 movlw 255 call direction_set ; # We are running at 16MHz. We want Tad to be as close to 1.6uS ; # as possible. 1/(16MHz/32) = 2uS which is about as close as ; # we are going to get. Thus, ADCS<2:0> = 010. ; line_number = 130 ; _adcon1 := 0x20 ;info 130, 17 movlw 32 bsf __rp0___byte, __rp0___bit movwf _adcon1 ; line_number = 132 ; _adcon0 := 0 ;info 132, 20 bcf __rp0___byte, __rp0___bit clrf _adcon0 ; # A/D result is left justified (10-bits) in ADRESH::ADRESL ; line_number = 134 ; _adfm := _false ;info 134, 22 bcf _adfm___byte, _adfm___bit ; # Use 5 volt voltage reference: ; line_number = 136 ; _vcfg := _false ;info 136, 23 bcf _vcfg___byte, _vcfg___bit ; # Turn on the A/D: ; line_number = 138 ; _adon := _true ;info 138, 24 bsf _adon___byte, _adon___bit ; line_number = 140 ; pulse_high := 0x12 ;info 140, 25 movlw 18 movwf pulse_high ; line_number = 141 ; pulse_low := 0x34 ;info 141, 27 movlw 52 movwf pulse_low ; line_number = 142 ; analog_threshold := 0x7f ;info 142, 29 movlw 127 movwf analog_threshold ; line_number = 144 ; loop_forever start main__1: ; # Make sure that we have been selected: ; line_number = 146 ; rb2bus_error := _true ;info 146, 31 bsf rb2bus_error___byte, rb2bus_error___bit ; line_number = 147 ; while rb2bus_error start main__2: ;info 147, 32 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; No 1TEST: true.size=4 false.size=0 ; No 2TEST: true.size=4 false.size=0 ; 1GOTO: Single test with GOTO btfss rb2bus_error___byte, rb2bus_error___bit goto main__3 ; line_number = 148 ; call rb2bus_select_wait() ;info 148, 34 call rb2bus_select_wait ; line_number = 149 ; command := rb2bus_byte_get() ;info 149, 35 call rb2bus_byte_get movwf main__command goto main__2 ; Recombine size1 = 0 || size2 = 0 main__3: ; line_number = 147 ; while rb2bus_error done ; line_number = 151 ; switch command >> 6 start ;info 151, 38 ; switch_before:(data:00=uu=>00 code:X0=cu=>X0) size=7 movlw main__44>>8 movwf __pclath main__45 equ globals___0+65 swapf main__command,w movwf main__45 rrf main__45,f rrf main__45,w andlw 3 ; switch after expression:(data:00=uu=>00 code:X0=cu=>X0) addlw main__44 movwf __pcl ; page_group 4 main__44: goto main__41 goto main__46 goto main__42 goto main__43 ; line_number = 152 ; case 0 main__41: ; # 00xx xxxx: ; line_number = 154 ; switch (command >> 3) & 7 start ;info 154, 51 ; switch_before:(data:XX=cc=>XX code:XX=cc=>XX) size=0 movlw main__22>>8 movwf __pclath main__23 equ globals___0+65 rrf main__command,w movwf main__23 rrf main__23,f rrf main__23,w andlw 7 ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw main__22 movwf __pcl ; page_group 8 main__22: goto main__17 goto main__24 goto main__18 goto main__19 goto main__20 goto main__20 goto main__21 goto main__21 ; line_number = 155 ; case 0 main__17: ; # 0000 0xxx: ; line_number = 157 ; switch command & 7 start ;info 157, 68 ; switch_before:(data:XX=cc=>XX code:XX=cc=>XX) size=0 ; line_number = 182 ; case_maximum 7 movlw main__13>>8 movwf __pclath movlw 7 andwf main__command,w ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw main__13 movwf __pcl ; page_group 8 main__13: goto main__7 goto main__8 goto main__9 goto main__10 goto main__11 goto main__12 goto main__14 goto main__14 ; line_number = 158 ; case 0 main__7: ; # 0000 0000 (Digital8_Read): ; line_number = 160 ; call rb2bus_byte_put(digital_read()) ;info 160, 82 call digital_read call rb2bus_byte_put goto main__14 ; line_number = 161 ; case 1 main__8: ; # 0000 0001 (Digital8_Write): ; line_number = 163 ; command := rb2bus_byte_get() ;info 163, 85 call rb2bus_byte_get movwf main__command ; line_number = 164 ; if !rb2bus_error start ;info 164, 87 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc rb2bus_error___byte, rb2bus_error___bit goto main__4 ; line_number = 165 ; call digital_set(command) ;info 165, 89 movf main__command,w call digital_set main__4: ; Recombine size1 = 0 || size2 = 0 ; line_number = 164 ; if !rb2bus_error done goto main__14 ; line_number = 166 ; case 2 main__9: ; # 0000 0010 (Direction_Read): ; line_number = 168 ; call rb2bus_byte_put(direction_read()) ;info 168, 92 call direction_read call rb2bus_byte_put goto main__14 ; line_number = 169 ; case 3 main__10: ; # 0000 0011 (Direction_Set): ; line_number = 171 ; command := rb2bus_byte_get() ;info 171, 95 call rb2bus_byte_get movwf main__command ; line_number = 172 ; if !rb2bus_error start ;info 172, 97 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc rb2bus_error___byte, rb2bus_error___bit goto main__5 ; line_number = 173 ; call direction_set(command) ;info 173, 99 movf main__command,w call direction_set main__5: ; Recombine size1 = 0 || size2 = 0 ; line_number = 172 ; if !rb2bus_error done goto main__14 ; line_number = 174 ; case 4 main__11: ; # 0000 0100 (Analog_Mask_Read): ; line_number = 176 ; call rb2bus_byte_put(analog_mask_read()) ;info 176, 102 call analog_mask_read call rb2bus_byte_put goto main__14 ; line_number = 177 ; case 5 main__12: ; # 0000 0101 (Analog_Mask_Set): ; line_number = 179 ; command := rb2bus_byte_get() ;info 179, 105 call rb2bus_byte_get movwf main__command ; line_number = 180 ; if !rb2bus_error start ;info 180, 107 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc rb2bus_error___byte, rb2bus_error___bit goto main__6 ; line_number = 181 ; call analog_mask_set(command) ;info 181, 109 movf main__command,w call analog_mask_set main__6: ; Recombine size1 = 0 || size2 = 0 ; line_number = 180 ; if !rb2bus_error done main__14: ; line_number = 157 ; switch command & 7 done goto main__24 ; line_number = 183 ; case 2 main__18: ; # 0001 0ccc (Analog8_Read): ; #result := analog_read(command & 7) ; line_number = 186 ; call rb2bus_byte_put(adc_msbs[command & 7]) ;info 186, 112 movlw 7 andwf main__command,w addlw adc_msbs movwf __fsr bcf __irp___byte, __irp___bit movf __indf,w call rb2bus_byte_put goto main__24 ; line_number = 187 ; case 3 main__19: ; # 0001 1ccc (Analog10_Read): ; line_number = 189 ; call rb2bus_byte_put(adc_lsbs[command & 7]) ;info 189, 120 movlw 7 andwf main__command,w addlw adc_lsbs movwf __fsr bcf __irp___byte, __irp___bit movf __indf,w call rb2bus_byte_put goto main__24 ; line_number = 190 ; case 4, 5 main__20: ; # 0010 dddd (Low Set): ; line_number = 192 ; call digital_set((digital_read() & 0xf0) | (command & 0xf)) ;info 192, 128 main__15 equ globals___0+65 call digital_read andlw 240 movwf main__15 movlw 15 andwf main__command,w iorwf main__15,w call digital_set goto main__24 ; line_number = 193 ; case 6, 7 main__21: ; # 0011 dddd (High Set): ; line_number = 195 ; call digital_set((command << 4) | (digital_read() & 0xf)) ;info 195, 136 main__16 equ globals___0+65 swapf main__command,w movwf main__16 movlw 240 andwf main__16,f call digital_read andlw 15 iorwf main__16,w call digital_set main__24: ; line_number = 154 ; switch (command >> 3) & 7 done goto main__46 ; line_number = 196 ; case 2 main__42: ; # 10xx xxxx: ; line_number = 198 ; switch (command >> 3) & 7 start ;info 198, 145 ; switch_before:(data:XX=cc=>XX code:XX=cc=>XX) size=0 movlw main__34>>8 movwf __pclath main__35 equ globals___0+65 rrf main__command,w movwf main__35 rrf main__35,f rrf main__35,w andlw 7 ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw main__34 movwf __pcl ; page_group 4 main__34: goto main__36 goto main__36 goto main__36 goto main__33 ; line_number = 199 ; case 3 main__33: ; # 1001 1xxx: ; line_number = 201 ; switch command & 7 start ;info 201, 158 ; switch_before:(data:XX=cc=>XX code:XX=cc=>XX) size=0 ; line_number = 202 ; case_maximum 7 movlw main__31>>8 movwf __pclath movlw 7 andwf main__command,w ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw main__31 movwf __pcl ; page_group 8 main__31: goto main__32 goto main__32 goto main__32 goto main__32 goto main__28 goto main__29 goto main__30 goto main__32 ; line_number = 203 ; case 4 main__28: ; # 1001 1100 (Threshold Get) ; line_number = 205 ; call rb2bus_byte_put(analog_threshold) ;info 205, 172 movf analog_threshold,w call rb2bus_byte_put goto main__32 ; line_number = 206 ; case 5 main__29: ; # 1001 1101 (Threshold Set) ; line_number = 208 ; analog_threshold := rb2bus_byte_get() ;info 208, 175 call rb2bus_byte_get movwf analog_threshold goto main__32 ; line_number = 209 ; case 6 main__30: ; # 1001 1110 (Analog Thresholded Get) ; line_number = 211 ; result := 0 ;info 211, 178 clrf main__result ; line_number = 212 ; channel := 0 ;info 212, 179 clrf main__channel ; line_number = 213 ; while channel < 8 start main__25: ;info 213, 180 movlw 8 subwf main__channel,w ; =>bit_code_emit@symbol(): sym=__c ; No 1TEST: true.size=0 false.size=14 ; No 2TEST: true.size=0 false.size=14 ; 1GOTO: Single test with GOTO btfsc __c___byte, __c___bit goto main__27 ; line_number = 214 ; high := adc_msbs[channel] ;info 214, 184 movf main__channel,w addlw adc_msbs movwf __fsr bcf __irp___byte, __irp___bit movf __indf,w movwf main__high ; line_number = 215 ; result := result >> 1 ;info 215, 190 ; Assignment of variable to self (no code needed) rrf main__result,f bcf main__result, 7 ; line_number = 216 ; if high >= analog_threshold start ;info 216, 192 movf analog_threshold,w subwf main__high,w ; =>bit_code_emit@symbol(): sym=__c ; 1TEST: Single test with code in skip slot btfsc __c___byte, __c___bit ; line_number = 217 ; result@7 := _true ;info 217, 195 main__select__26___byte equ main__result main__select__26___bit equ 7 bsf main__select__26___byte, main__select__26___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 216 ; if high >= analog_threshold done ; line_number = 218 ; channel := channel + 1 ;info 218, 196 incf main__channel,f goto main__25 main__27: ; Recombine size1 = 0 || size2 = 0 ; line_number = 213 ; while channel < 8 done ; line_number = 219 ; call rb2bus_byte_put(result) ;info 219, 198 movf main__result,w call rb2bus_byte_put main__32: ; line_number = 201 ; switch command & 7 done main__36: ; line_number = 198 ; switch (command >> 3) & 7 done goto main__46 ; line_number = 220 ; case 3 main__43: ; # 11xx xxxx: ; line_number = 222 ; switch (command >> 3) & 7 start ;info 222, 201 ; switch_before:(data:XX=cc=>XX code:XX=cc=>XX) size=0 movlw main__38>>8 movwf __pclath main__39 equ globals___0+65 rrf main__command,w movwf main__39 rrf main__39,f rrf main__39,w andlw 7 ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw main__38 movwf __pcl ; page_group 8 main__38: goto main__40 goto main__40 goto main__40 goto main__40 goto main__40 goto main__40 goto main__40 goto main__37 ; line_number = 223 ; case 7 main__37: ; # 1111 1xxx: ; line_number = 225 ; call rb2bus_command(command) ;info 225, 218 movf main__command,w call rb2bus_command main__40: ; line_number = 222 ; switch (command >> 3) & 7 done main__46: ; line_number = 151 ; switch command >> 6 done ; line_number = 144 ; loop_forever wrap-up goto main__1 ; line_number = 144 ; loop_forever done ; delay after procedure statements=non-uniform ; # Removed code for bit toggle and bit time: ; # case 1 ; # # 01xx xbbb: ; # switch command & 7 ; # case 0 ; # mask := 1 ; # case 1 ; # mask := 2 ; # case 2 ; # mask := 4 ; # case 3 ; # mask := 8 ; # case 4 ; # mask := 0x10 ; # case 5 ; # mask := 0x20 ; # case 6 ; # mask := 0x40 ; # case 7 ; # mask := 0x80 ; # mask_complement := 0xff ^ mask ; # switch (command >> 3) & 7 ; # case 0 ; # # 0100 0bbb (Direction Mask Bit Clear): ; # call direction_set(direction_read() & mask_complement) ; # case 1 ; # # 0100 1bbb (Direction Mask Bit Set): ; # call direction_set(direction_read() | mask) ; # case 2 ; # # 0101 0bbb (Analog Mask Bit Clear): ; # call analog_mask_set(analog_mask_read() & mask_complement) ; # case 3 ; # # 0101 1bbb (Analog Mask Bit Set): ; # call analog_mask_set(analog_mask_read() | mask) ; # case 4 ; # # 0110 0bbb (Digital Bit Clear): ; # call digital_set(digital_read() & mask_complement) ; # case 5 ; # # 0110 1bbb (Digital Bit Set): ; # call digital_set(digital_read() | mask) ; # case 6 ; # # 0111 1bbb (Digital Bit Toggle): ; # call digital_set(digital_read() ^ mask) ; # case 7 ; # # 0111 1bbb: ; # do_nothing ; # case 2 ; # # 10xx xxxx: ; # switch (command >> 3) & 7 ; # case_maximum 7 ; # case 0, 1 ; # # 1000 pphe (Pulse Time Configure): ; # if command@0 ; # # Enable: ; # ; # # Configure set prescale bits (pp) and clear rest: ; # _t1con := (command << 2) & 0x30 ; # ; # # Congifure Interrupt on Change Port A: ; # _ioca := 1 << io7_bit ; # _raif := _false ; # _raie := _true ; # ; # # Get interrupts turned on: ; # #_peie := _true ; # #_gie := _true ; # pulse_count := 0 ; # else ; # # Disable: ; # _t1con := 0 ; # _ioca := 0 ; # _raie := _false ; # #_gie := _false ; # ; # # Remember whether to use high or low pulses: ; # time_high := _false ; # if command@1 ; # time_high := _true ; # case 3 ; # # 1001 1xxx: ; # switch command & 7 ; # case_maximum 7 ; # case 0 ; # # 1001 1000 (Pulse Count Get): ; # call rb2bus_byte_put(pulse_count) ; # case 1 ; # # 1001 1001 (Pulse Count Set): ; # pulse_count := rb2bus_byte_get() ; # case 2 ; # # 1001 1010 (Pulse Get): ; # #_gie := _false ; # high := pulse_high ; # low := pulse_low ; # #_gie := _true ; # call rb2bus_byte_put(high) ; # call rb2bus_byte_put(low) ; # case 4 ; # # 1001 1100 (Threshold Get) ; # analog_threshold := rb2bus_byte_get() ; # case 5 ; # # 1001 1100 (Threshold Set) ; # call rb2bus_byte_put(analog_threshold) ; # case 6 ; # # 1001 1100 (Analog Thresholded Get) ; # result := 0 ; # channel := 0 ; # while channel < 8 ; # call analog_read(channel) ; # low := adc_lsbs[channel] ; # high := adc_msbs[channel] ; # result := result << 1 ; # temporary := (high << 6) | (low >> 2) ; # if temporary >= analog_threshold ; # result@0 := _true ; # channel := channel + 1 ; # call rb2bus_byte_put(result) ; line_number = 345 ;info 345, 221 ; procedure analog_read analog_read: ; Last argument is sitting in W; save into argument variable movwf analog_read__channel ; delay=4294967295 ; line_number = 346 ; argument channel byte analog_read__channel equ globals___0+43 ; line_number = 347 ; returns byte ; # Read A/D channel {channel} and return it. The bits are ; # stored into {adc_lsbs}[] and {adc_msbs}[]. ; line_number = 352 ; local adc_channel byte analog_read__adc_channel equ globals___0+40 ; line_number = 353 ; local adc_high byte analog_read__adc_high equ globals___0+41 ; line_number = 354 ; local adc_low byte analog_read__adc_low equ globals___0+42 ; # The IO8 pin wiring is different from the ; # "logical" pins. Do the remapping here: ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 358 ; channel := channel & 7 ;info 358, 222 movlw 7 andwf analog_read__channel,f ; line_number = 359 ; switch channel start ;info 359, 224 ; switch_before:(data:00=uu=>00 code:X0=cu=>X0) size=3 movlw analog_read__9>>8 movwf __pclath movf analog_read__channel,w ; switch after expression:(data:00=uu=>00 code:X0=cu=>X0) addlw analog_read__9 movwf __pcl ; page_group 8 analog_read__9: goto analog_read__1 goto analog_read__2 goto analog_read__3 goto analog_read__4 goto analog_read__5 goto analog_read__6 goto analog_read__7 goto analog_read__8 ; line_number = 360 ; case 0 analog_read__1: ; line_number = 361 ; adc_channel := 4 ;info 361, 237 movlw 4 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 362 ; case 1 analog_read__2: ; line_number = 363 ; adc_channel := 3 ;info 363, 240 movlw 3 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 364 ; case 2 analog_read__3: ; line_number = 365 ; adc_channel := 5 ;info 365, 243 movlw 5 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 366 ; case 3 analog_read__4: ; line_number = 367 ; adc_channel := 0 ;info 367, 246 clrf analog_read__adc_channel goto analog_read__10 ; line_number = 368 ; case 4 analog_read__5: ; line_number = 369 ; adc_channel := 6 ;info 369, 248 movlw 6 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 370 ; case 5 analog_read__6: ; line_number = 371 ; adc_channel := 1 ;info 371, 251 movlw 1 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 372 ; case 6 analog_read__7: ; line_number = 373 ; adc_channel := 7 ;info 373, 254 movlw 7 movwf analog_read__adc_channel goto analog_read__10 ; line_number = 374 ; case 7 analog_read__8: ; line_number = 375 ; adc_channel := 2 ;info 375, 257 movlw 2 movwf analog_read__adc_channel analog_read__10: ; line_number = 359 ; switch channel done ; # Select the channel while keeping the A/D on: ; line_number = 378 ; _adcon0 := (adc_channel << 2) | 1 ;info 378, 259 analog_read__11 equ globals___0+66 rlf analog_read__adc_channel,w movwf analog_read__11 rlf analog_read__11,w andlw 252 iorlw 1 movwf _adcon0 ; # It can take up to 20 uS for the A/D to stablize: ; line_number = 380 ; delay 20 * microsecond start ;info 380, 265 ; Delay expression evaluates to 100 ; line_number = 381 ; do_nothing ;info 381, 265 ; Delay 100 cycles ; Delay loop takes 25 * 4 = 100 cycles movlw 25 analog_read__12: addlw 255 btfss __z___byte, __z___bit goto analog_read__12 ; line_number = 380 ; delay 20 * microsecond done ; # Now take the A/D sample: ; line_number = 384 ; _go := _true ;info 384, 269 bsf _go___byte, _go___bit ; line_number = 385 ; while _go start analog_read__13: ;info 385, 270 ; =>bit_code_emit@symbol(): sym=_go ; 1TEST: Single test with code in skip slot btfsc _go___byte, _go___bit ; line_number = 386 ; do_nothing ;info 386, 271 goto analog_read__13 ; Recombine size1 = 0 || size2 = 0 ; line_number = 385 ; while _go done ; # We've got the result: ; line_number = 389 ; adc_high := _adresh ;info 389, 272 movf _adresh,w movwf analog_read__adc_high ; line_number = 390 ; adc_low := _adresl ;info 390, 274 bsf __rp0___byte, __rp0___bit movf _adresl,w bcf __rp0___byte, __rp0___bit movwf analog_read__adc_low ; line_number = 391 ; adc_lsbs[channel] := adc_low ;info 391, 278 ; index_fsr_first movf analog_read__channel,w addlw adc_lsbs movwf __fsr bcf __irp___byte, __irp___bit movf analog_read__adc_low,w movwf __indf ; line_number = 392 ; adc_msbs[channel] := adc_high ;info 392, 284 ; index_fsr_first movf analog_read__channel,w addlw adc_msbs movwf __fsr bcf __irp___byte, __irp___bit movf analog_read__adc_high,w movwf __indf ; # Return the adc value as 8-bits: ; line_number = 395 ; return adc_high start ; line_number = 395 ;info 395, 290 movf analog_read__adc_high,w return ; line_number = 395 ; return adc_high done ; delay after procedure statements=non-uniform ; line_number = 398 ; global counter byte counter equ globals___0+44 ; line_number = 400 ;info 400, 292 ; procedure wait wait: ; arguments_none ; line_number = 402 ; returns_nothing ; line_number = 404 ; local channel byte wait__channel equ globals___0+45 ; line_number = 405 ; local adc_channel byte wait__adc_channel equ globals___0+46 ; line_number = 406 ; local adc_high byte wait__adc_high equ globals___0+47 ; line_number = 407 ; local adc_low byte wait__adc_low equ globals___0+48 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 409 ; switch counter & 3 start ;info 409, 292 ; switch_before:(data:00=uu=>00 code:X0=cu=>X0) size=0 movlw wait__22>>8 movwf __pclath movlw 3 andwf counter,w ; switch after expression:(data:00=uu=>00 code:X0=cu=>X0) addlw wait__22 movwf __pcl ; page_group 4 wait__22: goto wait__18 goto wait__19 goto wait__20 goto wait__21 ; line_number = 410 ; case 0 wait__18: ; line_number = 411 ; channel := (counter >> 2) & 7 ;info 411, 302 wait__1 equ globals___0+67 rrf counter,w movwf wait__1 rrf wait__1,w andlw 7 movwf wait__channel ; line_number = 412 ; switch channel start ;info 412, 307 ; switch_before:(data:00=uu=>00 code:XX=cc=>XX) size=5 movlw wait__10>>8 movwf __pclath movf wait__channel,w ; switch after expression:(data:00=uu=>00 code:XX=cc=>XX) addlw wait__10 movwf __pcl ; page_group 8 wait__10: goto wait__2 goto wait__3 goto wait__4 goto wait__5 goto wait__6 goto wait__7 goto wait__8 goto wait__9 ; line_number = 413 ; case 0 wait__2: ; line_number = 414 ; adc_channel := 5 ;info 414, 320 movlw 5 movwf wait__adc_channel goto wait__11 ; line_number = 415 ; case 1 wait__3: ; line_number = 416 ; adc_channel := 7 ;info 416, 323 movlw 7 movwf wait__adc_channel goto wait__11 ; line_number = 417 ; case 2 wait__4: ; line_number = 418 ; adc_channel := 6 ;info 418, 326 movlw 6 movwf wait__adc_channel goto wait__11 ; line_number = 419 ; case 3 wait__5: ; line_number = 420 ; adc_channel := 4 ;info 420, 329 movlw 4 movwf wait__adc_channel goto wait__11 ; line_number = 421 ; case 4 wait__6: ; line_number = 422 ; adc_channel := 1 ;info 422, 332 movlw 1 movwf wait__adc_channel goto wait__11 ; line_number = 423 ; case 5 wait__7: ; line_number = 424 ; adc_channel := 3 ;info 424, 335 movlw 3 movwf wait__adc_channel goto wait__11 ; line_number = 425 ; case 6 wait__8: ; line_number = 426 ; adc_channel := 0 ;info 426, 338 clrf wait__adc_channel goto wait__11 ; line_number = 427 ; case 7 wait__9: ; line_number = 428 ; adc_channel := 2 ;info 428, 340 movlw 2 movwf wait__adc_channel wait__11: ; line_number = 412 ; switch channel done ; # Select the channel while keeping the A/D on: ; line_number = 431 ; _adcon0 := (adc_channel << 2) | 1 ;info 431, 342 wait__12 equ globals___0+67 rlf wait__adc_channel,w movwf wait__12 rlf wait__12,w andlw 252 iorlw 1 movwf _adcon0 ; # It can take up to 20 uS for the A/D to stablize, ; # Do the first 10 microseconds here: ; line_number = 435 ; delay 10 * microsecond start ;info 435, 348 ; Delay expression evaluates to 50 ; line_number = 436 ; do_nothing ;info 436, 348 ; Delay 50 cycles ; Delay loop takes 12 * 4 = 48 cycles movlw 12 wait__13: addlw 255 btfss __z___byte, __z___bit goto wait__13 goto wait__14 wait__14: ; line_number = 435 ; delay 10 * microsecond done ; line_number = 437 ; counter := counter + 1 ;info 437, 353 incf counter,f goto wait__23 ; line_number = 438 ; case 1 wait__19: ; # Do the second 10 microseconds here: ; line_number = 440 ; delay 10 * microsecond start ;info 440, 355 ; Delay expression evaluates to 50 ; line_number = 441 ; do_nothing ;info 441, 355 ; Delay 50 cycles ; Delay loop takes 12 * 4 = 48 cycles movlw 12 wait__15: addlw 255 btfss __z___byte, __z___bit goto wait__15 goto wait__16 wait__16: ; line_number = 440 ; delay 10 * microsecond done ; # Start the A/D sample ; line_number = 444 ; _go := _true ;info 444, 360 bsf _go___byte, _go___bit ; line_number = 446 ; counter := counter + 1 ;info 446, 361 incf counter,f goto wait__23 ; line_number = 447 ; case 2 wait__20: ; line_number = 448 ; if !_go start ;info 448, 363 ; =>bit_code_emit@symbol(): sym=_go ; 1TEST: Single test with code in skip slot btfss _go___byte, _go___bit ; line_number = 449 ; counter := counter + 1 ;info 449, 364 incf counter,f ; Recombine size1 = 0 || size2 = 0 ; line_number = 448 ; if !_go done goto wait__23 ; line_number = 450 ; case 3 wait__21: ; # We've got the result: ; line_number = 452 ; channel := (counter >> 2) & 7 ;info 452, 366 wait__17 equ globals___0+67 rrf counter,w movwf wait__17 rrf wait__17,w andlw 7 movwf wait__channel ; line_number = 453 ; adc_high := _adresh ;info 453, 371 movf _adresh,w movwf wait__adc_high ; line_number = 454 ; adc_low := _adresl ;info 454, 373 bsf __rp0___byte, __rp0___bit movf _adresl,w bcf __rp0___byte, __rp0___bit movwf wait__adc_low ; line_number = 455 ; adc_lsbs[channel] := adc_low ;info 455, 377 ; index_fsr_first movf wait__channel,w addlw adc_lsbs movwf __fsr bcf __irp___byte, __irp___bit movf wait__adc_low,w movwf __indf ; line_number = 456 ; adc_msbs[channel] := adc_high ;info 456, 383 ; index_fsr_first movf wait__channel,w addlw adc_msbs movwf __fsr bcf __irp___byte, __irp___bit movf wait__adc_high,w movwf __indf ; line_number = 457 ; counter := counter + 1 ;info 457, 389 incf counter,f wait__23: ; line_number = 409 ; switch counter & 3 done ; line_number = 459 ; do_nothing ;info 459, 390 ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 462 ; string id = "\16,0,8,3,3,6\IO8-C2\7\Gramson" start ; id = '\16,0,8,3,3,6\IO8-C2\7\Gramson' id: ; Temporarily save index into FSR movwf __fsr ; Initialize PCLATH to point to this code page movlw id___base>>8 movwf __pclath ; Restore index from FSR movf __fsr,w addlw id___base ; Index to the correct return value movwf __pcl ; page_group 20 id___base: retlw 16 retlw 0 retlw 8 retlw 3 retlw 3 retlw 6 retlw 73 retlw 79 retlw 56 retlw 45 retlw 67 retlw 50 retlw 7 retlw 71 retlw 114 retlw 97 retlw 109 retlw 115 retlw 111 retlw 110 ; line_number = 462 ; string id = "\16,0,8,3,3,6\IO8-C2\7\Gramson" start ; line_number = 464 ;info 464, 417 ; procedure analog_mask_read analog_mask_read: ; arguments_none ; line_number = 466 ; returns byte ; # This procedure will return the analog selection bits. ; line_number = 470 ; local mask byte analog_mask_read__mask equ globals___0+49 ; line_number = 471 ; local result byte analog_mask_read__result equ globals___0+50 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 473 ; result := 0 ;info 473, 417 clrf analog_mask_read__result ; line_number = 474 ; mask := _ansel ;info 474, 418 bsf __rp0___byte, __rp0___bit movf _ansel,w bcf __rp0___byte, __rp0___bit movwf analog_mask_read__mask ; line_number = 475 ; if mask@0 start ;info 475, 422 analog_mask_read__select__2___byte equ analog_mask_read__mask analog_mask_read__select__2___bit equ 0 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__2 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__2___byte, analog_mask_read__select__2___bit ; line_number = 476 ; result@5 := _true ;info 476, 423 analog_mask_read__select__1___byte equ analog_mask_read__result analog_mask_read__select__1___bit equ 5 bsf analog_mask_read__select__1___byte, analog_mask_read__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 475 ; if mask@0 done ; line_number = 477 ; if mask@1 start ;info 477, 424 analog_mask_read__select__4___byte equ analog_mask_read__mask analog_mask_read__select__4___bit equ 1 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__4 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__4___byte, analog_mask_read__select__4___bit ; line_number = 478 ; result@7 := _true ;info 478, 425 analog_mask_read__select__3___byte equ analog_mask_read__result analog_mask_read__select__3___bit equ 7 bsf analog_mask_read__select__3___byte, analog_mask_read__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 477 ; if mask@1 done ; line_number = 479 ; if mask@2 start ;info 479, 426 analog_mask_read__select__6___byte equ analog_mask_read__mask analog_mask_read__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__6 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__6___byte, analog_mask_read__select__6___bit ; line_number = 480 ; result@6 := _true ;info 480, 427 analog_mask_read__select__5___byte equ analog_mask_read__result analog_mask_read__select__5___bit equ 6 bsf analog_mask_read__select__5___byte, analog_mask_read__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 479 ; if mask@2 done ; line_number = 481 ; if mask@3 start ;info 481, 428 analog_mask_read__select__8___byte equ analog_mask_read__mask analog_mask_read__select__8___bit equ 3 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__8 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__8___byte, analog_mask_read__select__8___bit ; line_number = 482 ; result@4 := _true ;info 482, 429 analog_mask_read__select__7___byte equ analog_mask_read__result analog_mask_read__select__7___bit equ 4 bsf analog_mask_read__select__7___byte, analog_mask_read__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 481 ; if mask@3 done ; line_number = 483 ; if mask@4 start ;info 483, 430 analog_mask_read__select__10___byte equ analog_mask_read__mask analog_mask_read__select__10___bit equ 4 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__10 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__10___byte, analog_mask_read__select__10___bit ; line_number = 484 ; result@1 := _true ;info 484, 431 analog_mask_read__select__9___byte equ analog_mask_read__result analog_mask_read__select__9___bit equ 1 bsf analog_mask_read__select__9___byte, analog_mask_read__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 483 ; if mask@4 done ; line_number = 485 ; if mask@5 start ;info 485, 432 analog_mask_read__select__12___byte equ analog_mask_read__mask analog_mask_read__select__12___bit equ 5 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__12 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__12___byte, analog_mask_read__select__12___bit ; line_number = 486 ; result@3 := _true ;info 486, 433 analog_mask_read__select__11___byte equ analog_mask_read__result analog_mask_read__select__11___bit equ 3 bsf analog_mask_read__select__11___byte, analog_mask_read__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 485 ; if mask@5 done ; line_number = 487 ; if mask@6 start ;info 487, 434 analog_mask_read__select__14___byte equ analog_mask_read__mask analog_mask_read__select__14___bit equ 6 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__14 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__14___byte, analog_mask_read__select__14___bit ; line_number = 488 ; result@0 := _true ;info 488, 435 analog_mask_read__select__13___byte equ analog_mask_read__result analog_mask_read__select__13___bit equ 0 bsf analog_mask_read__select__13___byte, analog_mask_read__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 487 ; if mask@6 done ; line_number = 489 ; if mask@7 start ;info 489, 436 analog_mask_read__select__16___byte equ analog_mask_read__mask analog_mask_read__select__16___bit equ 7 ; =>bit_code_emit@symbol(): sym=analog_mask_read__select__16 ; 1TEST: Single test with code in skip slot btfsc analog_mask_read__select__16___byte, analog_mask_read__select__16___bit ; line_number = 490 ; result@2 := _true ;info 490, 437 analog_mask_read__select__15___byte equ analog_mask_read__result analog_mask_read__select__15___bit equ 2 bsf analog_mask_read__select__15___byte, analog_mask_read__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 489 ; if mask@7 done ; line_number = 491 ; return result start ; line_number = 491 ;info 491, 438 movf analog_mask_read__result,w return ; line_number = 491 ; return result done ; delay after procedure statements=non-uniform ; line_number = 494 ;info 494, 440 ; procedure analog_mask_set analog_mask_set: ; Last argument is sitting in W; save into argument variable movwf analog_mask_set__analog ; delay=4294967295 ; line_number = 495 ; argument analog byte analog_mask_set__analog equ globals___0+52 ; line_number = 496 ; returns_nothing ; # This procedure will set the analog inputs to be equal to {analog}. ; line_number = 500 ; local mask byte analog_mask_set__mask equ globals___0+51 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 502 ; mask := 0 ;info 502, 441 clrf analog_mask_set__mask ; line_number = 503 ; if analog@0 start ;info 503, 442 analog_mask_set__select__2___byte equ analog_mask_set__analog analog_mask_set__select__2___bit equ 0 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__2 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__2___byte, analog_mask_set__select__2___bit ; line_number = 504 ; mask@6 := _true ;info 504, 443 analog_mask_set__select__1___byte equ analog_mask_set__mask analog_mask_set__select__1___bit equ 6 bsf analog_mask_set__select__1___byte, analog_mask_set__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 503 ; if analog@0 done ; line_number = 505 ; if analog@1 start ;info 505, 444 analog_mask_set__select__4___byte equ analog_mask_set__analog analog_mask_set__select__4___bit equ 1 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__4 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__4___byte, analog_mask_set__select__4___bit ; line_number = 506 ; mask@4 := _true ;info 506, 445 analog_mask_set__select__3___byte equ analog_mask_set__mask analog_mask_set__select__3___bit equ 4 bsf analog_mask_set__select__3___byte, analog_mask_set__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 505 ; if analog@1 done ; line_number = 507 ; if analog@2 start ;info 507, 446 analog_mask_set__select__6___byte equ analog_mask_set__analog analog_mask_set__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__6 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__6___byte, analog_mask_set__select__6___bit ; line_number = 508 ; mask@7 := _true ;info 508, 447 analog_mask_set__select__5___byte equ analog_mask_set__mask analog_mask_set__select__5___bit equ 7 bsf analog_mask_set__select__5___byte, analog_mask_set__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 507 ; if analog@2 done ; line_number = 509 ; if analog@3 start ;info 509, 448 analog_mask_set__select__8___byte equ analog_mask_set__analog analog_mask_set__select__8___bit equ 3 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__8 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__8___byte, analog_mask_set__select__8___bit ; line_number = 510 ; mask@5 := _true ;info 510, 449 analog_mask_set__select__7___byte equ analog_mask_set__mask analog_mask_set__select__7___bit equ 5 bsf analog_mask_set__select__7___byte, analog_mask_set__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 509 ; if analog@3 done ; line_number = 511 ; if analog@4 start ;info 511, 450 analog_mask_set__select__10___byte equ analog_mask_set__analog analog_mask_set__select__10___bit equ 4 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__10 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__10___byte, analog_mask_set__select__10___bit ; line_number = 512 ; mask@3 := _true ;info 512, 451 analog_mask_set__select__9___byte equ analog_mask_set__mask analog_mask_set__select__9___bit equ 3 bsf analog_mask_set__select__9___byte, analog_mask_set__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 511 ; if analog@4 done ; line_number = 513 ; if analog@5 start ;info 513, 452 analog_mask_set__select__12___byte equ analog_mask_set__analog analog_mask_set__select__12___bit equ 5 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__12 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__12___byte, analog_mask_set__select__12___bit ; line_number = 514 ; mask@0 := _true ;info 514, 453 analog_mask_set__select__11___byte equ analog_mask_set__mask analog_mask_set__select__11___bit equ 0 bsf analog_mask_set__select__11___byte, analog_mask_set__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 513 ; if analog@5 done ; line_number = 515 ; if analog@6 start ;info 515, 454 analog_mask_set__select__14___byte equ analog_mask_set__analog analog_mask_set__select__14___bit equ 6 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__14 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__14___byte, analog_mask_set__select__14___bit ; line_number = 516 ; mask@2 := _true ;info 516, 455 analog_mask_set__select__13___byte equ analog_mask_set__mask analog_mask_set__select__13___bit equ 2 bsf analog_mask_set__select__13___byte, analog_mask_set__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 515 ; if analog@6 done ; line_number = 517 ; if analog@7 start ;info 517, 456 analog_mask_set__select__16___byte equ analog_mask_set__analog analog_mask_set__select__16___bit equ 7 ; =>bit_code_emit@symbol(): sym=analog_mask_set__select__16 ; 1TEST: Single test with code in skip slot btfsc analog_mask_set__select__16___byte, analog_mask_set__select__16___bit ; line_number = 518 ; mask@1 := _true ;info 518, 457 analog_mask_set__select__15___byte equ analog_mask_set__mask analog_mask_set__select__15___bit equ 1 bsf analog_mask_set__select__15___byte, analog_mask_set__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 517 ; if analog@7 done ; line_number = 519 ; _ansel := mask ;info 519, 458 movf analog_mask_set__mask,w bsf __rp0___byte, __rp0___bit movwf _ansel ; delay after procedure statements=non-uniform bcf __rp0___byte, __rp0___bit ; Implied return retlw 0 ; line_number = 522 ;info 522, 463 ; procedure digital_read digital_read: ; arguments_none ; line_number = 524 ; returns byte ; # This procedure will return the digital bits corresponding to ; # the 8 digital data inputs. ; line_number = 529 ; local ra byte digital_read__ra equ globals___0+53 ; line_number = 530 ; local rc byte digital_read__rc equ globals___0+54 ; line_number = 531 ; local digital byte digital_read__digital equ globals___0+55 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 533 ; ra := _porta ;info 533, 463 movf _porta,w movwf digital_read__ra ; line_number = 534 ; rc := _portc ;info 534, 465 movf _portc,w movwf digital_read__rc ; line_number = 535 ; digital := 0 ;info 535, 467 clrf digital_read__digital ; line_number = 537 ; if rc@io0_bit start ;info 537, 468 digital_read__select__2___byte equ digital_read__rc digital_read__select__2___bit equ 1 ; =>bit_code_emit@symbol(): sym=digital_read__select__2 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__2___byte, digital_read__select__2___bit ; line_number = 538 ; digital@0 := _true ;info 538, 469 digital_read__select__1___byte equ digital_read__digital digital_read__select__1___bit equ 0 bsf digital_read__select__1___byte, digital_read__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 537 ; if rc@io0_bit done ; line_number = 539 ; if rc@io1_bit start ;info 539, 470 digital_read__select__4___byte equ digital_read__rc digital_read__select__4___bit equ 3 ; =>bit_code_emit@symbol(): sym=digital_read__select__4 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__4___byte, digital_read__select__4___bit ; line_number = 540 ; digital@1 := _true ;info 540, 471 digital_read__select__3___byte equ digital_read__digital digital_read__select__3___bit equ 1 bsf digital_read__select__3___byte, digital_read__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 539 ; if rc@io1_bit done ; line_number = 541 ; if rc@io2_bit start ;info 541, 472 digital_read__select__6___byte equ digital_read__rc digital_read__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=digital_read__select__6 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__6___byte, digital_read__select__6___bit ; line_number = 542 ; digital@2 := _true ;info 542, 473 digital_read__select__5___byte equ digital_read__digital digital_read__select__5___bit equ 2 bsf digital_read__select__5___byte, digital_read__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 541 ; if rc@io2_bit done ; line_number = 543 ; if rc@io3_bit start ;info 543, 474 digital_read__select__8___byte equ digital_read__rc digital_read__select__8___bit equ 0 ; =>bit_code_emit@symbol(): sym=digital_read__select__8 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__8___byte, digital_read__select__8___bit ; line_number = 544 ; digital@3 := _true ;info 544, 475 digital_read__select__7___byte equ digital_read__digital digital_read__select__7___bit equ 3 bsf digital_read__select__7___byte, digital_read__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 543 ; if rc@io3_bit done ; line_number = 545 ; if ra@io4_bit start ;info 545, 476 digital_read__select__10___byte equ digital_read__ra digital_read__select__10___bit equ 1 ; =>bit_code_emit@symbol(): sym=digital_read__select__10 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__10___byte, digital_read__select__10___bit ; line_number = 546 ; digital@4 := _true ;info 546, 477 digital_read__select__9___byte equ digital_read__digital digital_read__select__9___bit equ 4 bsf digital_read__select__9___byte, digital_read__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 545 ; if ra@io4_bit done ; line_number = 547 ; if ra@io5_bit start ;info 547, 478 digital_read__select__12___byte equ digital_read__ra digital_read__select__12___bit equ 4 ; =>bit_code_emit@symbol(): sym=digital_read__select__12 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__12___byte, digital_read__select__12___bit ; line_number = 548 ; digital@5 := _true ;info 548, 479 digital_read__select__11___byte equ digital_read__digital digital_read__select__11___bit equ 5 bsf digital_read__select__11___byte, digital_read__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 547 ; if ra@io5_bit done ; line_number = 549 ; if ra@io6_bit start ;info 549, 480 digital_read__select__14___byte equ digital_read__ra digital_read__select__14___bit equ 0 ; =>bit_code_emit@symbol(): sym=digital_read__select__14 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__14___byte, digital_read__select__14___bit ; line_number = 550 ; digital@6 := _true ;info 550, 481 digital_read__select__13___byte equ digital_read__digital digital_read__select__13___bit equ 6 bsf digital_read__select__13___byte, digital_read__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 549 ; if ra@io6_bit done ; line_number = 551 ; if ra@io7_bit start ;info 551, 482 digital_read__select__16___byte equ digital_read__ra digital_read__select__16___bit equ 2 ; =>bit_code_emit@symbol(): sym=digital_read__select__16 ; 1TEST: Single test with code in skip slot btfsc digital_read__select__16___byte, digital_read__select__16___bit ; line_number = 552 ; digital@7 := _true ;info 552, 483 digital_read__select__15___byte equ digital_read__digital digital_read__select__15___bit equ 7 bsf digital_read__select__15___byte, digital_read__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 551 ; if ra@io7_bit done ; line_number = 553 ; return digital start ; line_number = 553 ;info 553, 484 movf digital_read__digital,w return ; line_number = 553 ; return digital done ; delay after procedure statements=non-uniform ; line_number = 556 ;info 556, 486 ; procedure digital_set digital_set: ; Last argument is sitting in W; save into argument variable movwf digital_set__digital ; delay=4294967295 ; line_number = 557 ; argument digital byte digital_set__digital equ globals___0+58 ; line_number = 558 ; returns_nothing ; # This procedure will set the digital outputs to be equal to {digital}. ; line_number = 562 ; local ra byte digital_set__ra equ globals___0+56 ; line_number = 563 ; local rc byte digital_set__rc equ globals___0+57 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 565 ; ra := 0 ;info 565, 487 clrf digital_set__ra ; line_number = 566 ; rc := 0 ;info 566, 488 clrf digital_set__rc ; line_number = 567 ; if digital@0 start ;info 567, 489 digital_set__select__2___byte equ digital_set__digital digital_set__select__2___bit equ 0 ; =>bit_code_emit@symbol(): sym=digital_set__select__2 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__2___byte, digital_set__select__2___bit ; line_number = 568 ; rc@io0_bit := _true ;info 568, 490 digital_set__select__1___byte equ digital_set__rc digital_set__select__1___bit equ 1 bsf digital_set__select__1___byte, digital_set__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 567 ; if digital@0 done ; line_number = 569 ; if digital@1 start ;info 569, 491 digital_set__select__4___byte equ digital_set__digital digital_set__select__4___bit equ 1 ; =>bit_code_emit@symbol(): sym=digital_set__select__4 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__4___byte, digital_set__select__4___bit ; line_number = 570 ; rc@io1_bit := _true ;info 570, 492 digital_set__select__3___byte equ digital_set__rc digital_set__select__3___bit equ 3 bsf digital_set__select__3___byte, digital_set__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 569 ; if digital@1 done ; line_number = 571 ; if digital@2 start ;info 571, 493 digital_set__select__6___byte equ digital_set__digital digital_set__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=digital_set__select__6 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__6___byte, digital_set__select__6___bit ; line_number = 572 ; rc@io2_bit := _true ;info 572, 494 digital_set__select__5___byte equ digital_set__rc digital_set__select__5___bit equ 2 bsf digital_set__select__5___byte, digital_set__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 571 ; if digital@2 done ; line_number = 573 ; if digital@3 start ;info 573, 495 digital_set__select__8___byte equ digital_set__digital digital_set__select__8___bit equ 3 ; =>bit_code_emit@symbol(): sym=digital_set__select__8 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__8___byte, digital_set__select__8___bit ; line_number = 574 ; rc@io3_bit := _true ;info 574, 496 digital_set__select__7___byte equ digital_set__rc digital_set__select__7___bit equ 0 bsf digital_set__select__7___byte, digital_set__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 573 ; if digital@3 done ; line_number = 575 ; if digital@4 start ;info 575, 497 digital_set__select__10___byte equ digital_set__digital digital_set__select__10___bit equ 4 ; =>bit_code_emit@symbol(): sym=digital_set__select__10 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__10___byte, digital_set__select__10___bit ; line_number = 576 ; ra@io4_bit := _true ;info 576, 498 digital_set__select__9___byte equ digital_set__ra digital_set__select__9___bit equ 1 bsf digital_set__select__9___byte, digital_set__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 575 ; if digital@4 done ; line_number = 577 ; if digital@5 start ;info 577, 499 digital_set__select__12___byte equ digital_set__digital digital_set__select__12___bit equ 5 ; =>bit_code_emit@symbol(): sym=digital_set__select__12 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__12___byte, digital_set__select__12___bit ; line_number = 578 ; ra@io5_bit := _true ;info 578, 500 digital_set__select__11___byte equ digital_set__ra digital_set__select__11___bit equ 4 bsf digital_set__select__11___byte, digital_set__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 577 ; if digital@5 done ; line_number = 579 ; if digital@6 start ;info 579, 501 digital_set__select__14___byte equ digital_set__digital digital_set__select__14___bit equ 6 ; =>bit_code_emit@symbol(): sym=digital_set__select__14 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__14___byte, digital_set__select__14___bit ; line_number = 580 ; ra@io6_bit := _true ;info 580, 502 digital_set__select__13___byte equ digital_set__ra digital_set__select__13___bit equ 0 bsf digital_set__select__13___byte, digital_set__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 579 ; if digital@6 done ; line_number = 581 ; if digital@7 start ;info 581, 503 digital_set__select__16___byte equ digital_set__digital digital_set__select__16___bit equ 7 ; =>bit_code_emit@symbol(): sym=digital_set__select__16 ; 1TEST: Single test with code in skip slot btfsc digital_set__select__16___byte, digital_set__select__16___bit ; line_number = 582 ; ra@io7_bit := _true ;info 582, 504 digital_set__select__15___byte equ digital_set__ra digital_set__select__15___bit equ 2 bsf digital_set__select__15___byte, digital_set__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 581 ; if digital@7 done ; line_number = 583 ; _porta := ra ;info 583, 505 movf digital_set__ra,w movwf _porta ; line_number = 584 ; _portc := rc ;info 584, 507 movf digital_set__rc,w movwf _portc ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 587 ;info 587, 510 ; procedure direction_read direction_read: ; arguments_none ; line_number = 589 ; returns byte ; # This procedure will return the digital bits corresponding to ; # the 8 digital data inputs. ; line_number = 594 ; local trisa byte direction_read__trisa equ globals___0+59 ; line_number = 595 ; local trisc byte direction_read__trisc equ globals___0+60 ; line_number = 596 ; local direction byte direction_read__direction equ globals___0+61 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 598 ; direction := 0 ;info 598, 510 clrf direction_read__direction ; # Get all data into data bank 0: ; line_number = 600 ; trisa := _trisa ;info 600, 511 bsf __rp0___byte, __rp0___bit movf _trisa,w bcf __rp0___byte, __rp0___bit movwf direction_read__trisa ; line_number = 601 ; trisc := _trisc ;info 601, 515 bsf __rp0___byte, __rp0___bit movf _trisc,w bcf __rp0___byte, __rp0___bit movwf direction_read__trisc ; line_number = 603 ; if trisc@io0_bit start ;info 603, 519 direction_read__select__2___byte equ direction_read__trisc direction_read__select__2___bit equ 1 ; =>bit_code_emit@symbol(): sym=direction_read__select__2 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__2___byte, direction_read__select__2___bit ; line_number = 604 ; direction@0 := _true ;info 604, 520 direction_read__select__1___byte equ direction_read__direction direction_read__select__1___bit equ 0 bsf direction_read__select__1___byte, direction_read__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 603 ; if trisc@io0_bit done ; line_number = 605 ; if trisc@io1_bit start ;info 605, 521 direction_read__select__4___byte equ direction_read__trisc direction_read__select__4___bit equ 3 ; =>bit_code_emit@symbol(): sym=direction_read__select__4 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__4___byte, direction_read__select__4___bit ; line_number = 606 ; direction@1 := _true ;info 606, 522 direction_read__select__3___byte equ direction_read__direction direction_read__select__3___bit equ 1 bsf direction_read__select__3___byte, direction_read__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 605 ; if trisc@io1_bit done ; line_number = 607 ; if trisc@io2_bit start ;info 607, 523 direction_read__select__6___byte equ direction_read__trisc direction_read__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=direction_read__select__6 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__6___byte, direction_read__select__6___bit ; line_number = 608 ; direction@2 := _true ;info 608, 524 direction_read__select__5___byte equ direction_read__direction direction_read__select__5___bit equ 2 bsf direction_read__select__5___byte, direction_read__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 607 ; if trisc@io2_bit done ; line_number = 609 ; if trisc@io3_bit start ;info 609, 525 direction_read__select__8___byte equ direction_read__trisc direction_read__select__8___bit equ 0 ; =>bit_code_emit@symbol(): sym=direction_read__select__8 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__8___byte, direction_read__select__8___bit ; line_number = 610 ; direction@3 := _true ;info 610, 526 direction_read__select__7___byte equ direction_read__direction direction_read__select__7___bit equ 3 bsf direction_read__select__7___byte, direction_read__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 609 ; if trisc@io3_bit done ; line_number = 611 ; if trisa@io4_bit start ;info 611, 527 direction_read__select__10___byte equ direction_read__trisa direction_read__select__10___bit equ 1 ; =>bit_code_emit@symbol(): sym=direction_read__select__10 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__10___byte, direction_read__select__10___bit ; line_number = 612 ; direction@4 := _true ;info 612, 528 direction_read__select__9___byte equ direction_read__direction direction_read__select__9___bit equ 4 bsf direction_read__select__9___byte, direction_read__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 611 ; if trisa@io4_bit done ; line_number = 613 ; if trisa@io5_bit start ;info 613, 529 direction_read__select__12___byte equ direction_read__trisa direction_read__select__12___bit equ 4 ; =>bit_code_emit@symbol(): sym=direction_read__select__12 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__12___byte, direction_read__select__12___bit ; line_number = 614 ; direction@5 := _true ;info 614, 530 direction_read__select__11___byte equ direction_read__direction direction_read__select__11___bit equ 5 bsf direction_read__select__11___byte, direction_read__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 613 ; if trisa@io5_bit done ; line_number = 615 ; if trisa@io6_bit start ;info 615, 531 direction_read__select__14___byte equ direction_read__trisa direction_read__select__14___bit equ 0 ; =>bit_code_emit@symbol(): sym=direction_read__select__14 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__14___byte, direction_read__select__14___bit ; line_number = 616 ; direction@6 := _true ;info 616, 532 direction_read__select__13___byte equ direction_read__direction direction_read__select__13___bit equ 6 bsf direction_read__select__13___byte, direction_read__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 615 ; if trisa@io6_bit done ; line_number = 617 ; if trisa@io7_bit start ;info 617, 533 direction_read__select__16___byte equ direction_read__trisa direction_read__select__16___bit equ 2 ; =>bit_code_emit@symbol(): sym=direction_read__select__16 ; 1TEST: Single test with code in skip slot btfsc direction_read__select__16___byte, direction_read__select__16___bit ; line_number = 618 ; direction@7 := _true ;info 618, 534 direction_read__select__15___byte equ direction_read__direction direction_read__select__15___bit equ 7 bsf direction_read__select__15___byte, direction_read__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 617 ; if trisa@io7_bit done ; line_number = 619 ; return direction start ; line_number = 619 ;info 619, 535 movf direction_read__direction,w return ; line_number = 619 ; return direction done ; delay after procedure statements=non-uniform ; line_number = 622 ;info 622, 537 ; procedure direction_set direction_set: ; Last argument is sitting in W; save into argument variable movwf direction_set__direction ; delay=4294967295 ; line_number = 623 ; argument direction byte direction_set__direction equ globals___0+64 ; line_number = 624 ; returns_nothing ; # This procedure will set the direction outputs to be equal to {direction}. ; line_number = 628 ; local trisa byte direction_set__trisa equ globals___0+62 ; line_number = 629 ; local trisc byte direction_set__trisc equ globals___0+63 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 631 ; trisa := 0xc0 ;info 631, 538 movlw 192 movwf direction_set__trisa ; line_number = 632 ; trisc := 0xc0 ;info 632, 540 movlw 192 movwf direction_set__trisc ; line_number = 633 ; if direction@0 start ;info 633, 542 direction_set__select__2___byte equ direction_set__direction direction_set__select__2___bit equ 0 ; =>bit_code_emit@symbol(): sym=direction_set__select__2 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__2___byte, direction_set__select__2___bit ; line_number = 634 ; trisc@io0_bit := _true ;info 634, 543 direction_set__select__1___byte equ direction_set__trisc direction_set__select__1___bit equ 1 bsf direction_set__select__1___byte, direction_set__select__1___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 633 ; if direction@0 done ; line_number = 635 ; if direction@1 start ;info 635, 544 direction_set__select__4___byte equ direction_set__direction direction_set__select__4___bit equ 1 ; =>bit_code_emit@symbol(): sym=direction_set__select__4 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__4___byte, direction_set__select__4___bit ; line_number = 636 ; trisc@io1_bit := _true ;info 636, 545 direction_set__select__3___byte equ direction_set__trisc direction_set__select__3___bit equ 3 bsf direction_set__select__3___byte, direction_set__select__3___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 635 ; if direction@1 done ; line_number = 637 ; if direction@2 start ;info 637, 546 direction_set__select__6___byte equ direction_set__direction direction_set__select__6___bit equ 2 ; =>bit_code_emit@symbol(): sym=direction_set__select__6 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__6___byte, direction_set__select__6___bit ; line_number = 638 ; trisc@io2_bit := _true ;info 638, 547 direction_set__select__5___byte equ direction_set__trisc direction_set__select__5___bit equ 2 bsf direction_set__select__5___byte, direction_set__select__5___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 637 ; if direction@2 done ; line_number = 639 ; if direction@3 start ;info 639, 548 direction_set__select__8___byte equ direction_set__direction direction_set__select__8___bit equ 3 ; =>bit_code_emit@symbol(): sym=direction_set__select__8 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__8___byte, direction_set__select__8___bit ; line_number = 640 ; trisc@io3_bit := _true ;info 640, 549 direction_set__select__7___byte equ direction_set__trisc direction_set__select__7___bit equ 0 bsf direction_set__select__7___byte, direction_set__select__7___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 639 ; if direction@3 done ; line_number = 641 ; if direction@4 start ;info 641, 550 direction_set__select__10___byte equ direction_set__direction direction_set__select__10___bit equ 4 ; =>bit_code_emit@symbol(): sym=direction_set__select__10 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__10___byte, direction_set__select__10___bit ; line_number = 642 ; trisa@io4_bit := _true ;info 642, 551 direction_set__select__9___byte equ direction_set__trisa direction_set__select__9___bit equ 1 bsf direction_set__select__9___byte, direction_set__select__9___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 641 ; if direction@4 done ; line_number = 643 ; if direction@5 start ;info 643, 552 direction_set__select__12___byte equ direction_set__direction direction_set__select__12___bit equ 5 ; =>bit_code_emit@symbol(): sym=direction_set__select__12 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__12___byte, direction_set__select__12___bit ; line_number = 644 ; trisa@io5_bit := _true ;info 644, 553 direction_set__select__11___byte equ direction_set__trisa direction_set__select__11___bit equ 4 bsf direction_set__select__11___byte, direction_set__select__11___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 643 ; if direction@5 done ; line_number = 645 ; if direction@6 start ;info 645, 554 direction_set__select__14___byte equ direction_set__direction direction_set__select__14___bit equ 6 ; =>bit_code_emit@symbol(): sym=direction_set__select__14 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__14___byte, direction_set__select__14___bit ; line_number = 646 ; trisa@io6_bit := _true ;info 646, 555 direction_set__select__13___byte equ direction_set__trisa direction_set__select__13___bit equ 0 bsf direction_set__select__13___byte, direction_set__select__13___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 645 ; if direction@6 done ; line_number = 647 ; if direction@7 start ;info 647, 556 direction_set__select__16___byte equ direction_set__direction direction_set__select__16___bit equ 7 ; =>bit_code_emit@symbol(): sym=direction_set__select__16 ; 1TEST: Single test with code in skip slot btfsc direction_set__select__16___byte, direction_set__select__16___bit ; line_number = 648 ; trisa@io7_bit := _true ;info 648, 557 direction_set__select__15___byte equ direction_set__trisa direction_set__select__15___bit equ 2 bsf direction_set__select__15___byte, direction_set__select__15___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 647 ; if direction@7 done ; line_number = 649 ; trisc@rx_bit := _true ;info 649, 558 direction_set__select__17___byte equ direction_set__trisc direction_set__select__17___bit equ 5 bsf direction_set__select__17___byte, direction_set__select__17___bit ; line_number = 650 ; trisc@tx_bit := _true ;info 650, 559 direction_set__select__18___byte equ direction_set__trisc direction_set__select__18___bit equ 4 bsf direction_set__select__18___byte, direction_set__select__18___bit ; line_number = 651 ; _trisa := trisa ;info 651, 560 movf direction_set__trisa,w bsf __rp0___byte, __rp0___bit movwf _trisa ; line_number = 652 ; _trisc := trisc ;info 652, 563 bcf __rp0___byte, __rp0___bit movf direction_set__trisc,w bsf __rp0___byte, __rp0___bit movwf _trisc ; delay after procedure statements=non-uniform bcf __rp0___byte, __rp0___bit ; Implied return retlw 0 ; Appending 8 delayed procedures to code bank 0 ; buffer = 'rb2bus' ; line_number = 57 ;info 57, 569 ; procedure rb2bus_select_wait rb2bus_select_wait: ; arguments_none ; line_number = 59 ; returns_nothing ; # This procedure will in an infinite loop until the select ; # address matches {rb2bus_address}. {rb2bus_address} is ; # typically set in the {rb2bus_initialize} procedure. ; # ; # This module will repeatably call the {wait} procedure until ; # it is properly selected. ; line_number = 68 ; local value byte rb2bus_select_wait__value equ globals___0+2 ; line_number = 69 ; local address_bit bit rb2bus_select_wait__address_bit___byte equ globals___0+79 rb2bus_select_wait__address_bit___bit equ 2 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 71 ; rb2bus_error := _false ;info 71, 569 bcf rb2bus_error___byte, rb2bus_error___bit ; line_number = 72 ; while !rb2bus_selected start rb2bus_select_wait__1: ;info 72, 570 ; =>bit_code_emit@symbol(): sym=rb2bus_selected ; No 1TEST: true.size=0 false.size=25 ; No 2TEST: true.size=0 false.size=25 ; 1GOTO: Single test with GOTO btfsc rb2bus_selected___byte, rb2bus_selected___bit goto rb2bus_select_wait__6 ; line_number = 73 ; _adden := _true ;info 73, 572 bsf _adden___byte, _adden___bit ; # Wait for a byte to arrive. ; line_number = 75 ; while !_rcif start rb2bus_select_wait__2: ;info 75, 573 ; =>bit_code_emit@symbol(): sym=_rcif ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc _rcif___byte, _rcif___bit goto rb2bus_select_wait__3 ; line_number = 76 ; call wait() ;info 76, 575 call wait goto rb2bus_select_wait__2 rb2bus_select_wait__3: ; Recombine size1 = 0 || size2 = 0 ; line_number = 75 ; while !_rcif done ; # Capture the received value: ; line_number = 79 ; address_bit := _false ;info 79, 577 bcf rb2bus_select_wait__address_bit___byte, rb2bus_select_wait__address_bit___bit ; line_number = 80 ; if _rx9d start ;info 80, 578 ; =>bit_code_emit@symbol(): sym=_rx9d ; 1TEST: Single test with code in skip slot btfsc _rx9d___byte, _rx9d___bit ; line_number = 81 ; address_bit := _true ;info 81, 579 bsf rb2bus_select_wait__address_bit___byte, rb2bus_select_wait__address_bit___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 80 ; if _rx9d done ; line_number = 82 ; value := _rcreg ;info 82, 580 movf _rcreg,w movwf rb2bus_select_wait__value ; # Clear any UART errors by toggling {_cren}: ; line_number = 85 ; if _oerr start ;info 85, 582 ; =>bit_code_emit@symbol(): sym=_oerr ; 1TEST: Single test with code in skip slot btfsc _oerr___byte, _oerr___bit ; line_number = 86 ; _cren := _false ;info 86, 583 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 85 ; if _oerr done ; line_number = 87 ; if _ferr start ;info 87, 584 ; =>bit_code_emit@symbol(): sym=_ferr ; 1TEST: Single test with code in skip slot btfsc _ferr___byte, _ferr___bit ; line_number = 88 ; _cren := _false ;info 88, 585 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 87 ; if _ferr done ; line_number = 89 ; _cren := _true ;info 89, 586 bsf _cren___byte, _cren___bit ; line_number = 91 ; if address_bit start ;info 91, 587 ; =>bit_code_emit@symbol(): sym=rb2bus_select_wait__address_bit ; No 1TEST: true.size=7 false.size=0 ; No 2TEST: true.size=7 false.size=0 ; 1GOTO: Single test with GOTO btfss rb2bus_select_wait__address_bit___byte, rb2bus_select_wait__address_bit___bit goto rb2bus_select_wait__5 ; line_number = 92 ; if value = rb2bus_address start ;info 92, 589 ; Left minus Right movf rb2bus_address,w subwf rb2bus_select_wait__value,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=3 false.size=0 ; No 2TEST: true.size=3 false.size=0 ; 1GOTO: Single test with GOTO btfss __z___byte, __z___bit goto rb2bus_select_wait__4 ; line_number = 93 ; rb2bus_selected := _true ;info 93, 593 bsf rb2bus_selected___byte, rb2bus_selected___bit ; line_number = 94 ; call rb2bus_byte_put(rb2_ok) ;info 94, 594 movlw 165 call rb2bus_byte_put ; Recombine size1 = 0 || size2 = 0 rb2bus_select_wait__4: ; line_number = 92 ; if value = rb2bus_address done ; Recombine size1 = 0 || size2 = 0 rb2bus_select_wait__5: ; line_number = 91 ; if address_bit done goto rb2bus_select_wait__1 rb2bus_select_wait__6: ; Recombine size1 = 0 || size2 = 0 ; line_number = 72 ; while !rb2bus_selected done ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 97 ;info 97, 598 ; procedure rb2bus_deselect rb2bus_deselect: ; arguments_none ; line_number = 99 ; returns_nothing ; # This procedure forces this module into the deselected state until ; # it is reselected by some master module on the bus. ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 104 ; rb2bus_selected := _false ;info 104, 598 bcf rb2bus_selected___byte, rb2bus_selected___bit ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 107 ;info 107, 600 ; procedure rb2bus_byte_get rb2bus_byte_get: ; arguments_none ; line_number = 109 ; returns byte ; # This procedure will return the next byte received from the bus. ; # The address (9th) bit is stored in the global {is_address}. ; # ; # If {rb2bus_error} is set, 0 is returned. Otherwise, the {wait} ; # procedure is repeatably called until a command byte is successfully ; # received. If an module select byte comes in, we enter a bus ; # error condition by setting {rb2bus_error} and returning 0. ; line_number = 119 ; local value byte rb2bus_byte_get__value equ globals___0+3 ; line_number = 120 ; local address_bit bit rb2bus_byte_get__address_bit___byte equ globals___0+79 rb2bus_byte_get__address_bit___bit equ 3 ; # Return 0 in a bus flush condition to get us back to {rb2bus_select_wait}: ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 123 ; if rb2bus_error start ;info 123, 600 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; 1TEST: Single test with code in skip slot btfsc rb2bus_error___byte, rb2bus_error___bit ; line_number = 124 ; return 0 start ; line_number = 124 ;info 124, 601 retlw 0 ; line_number = 124 ; return 0 done ; Recombine size1 = 0 || size2 = 0 ; line_number = 123 ; if rb2bus_error done ; # Wait for a byte to arrive. ; line_number = 127 ; _adden := _false ;info 127, 602 bcf _adden___byte, _adden___bit ; line_number = 128 ; while !_rcif start rb2bus_byte_get__1: ;info 128, 603 ; =>bit_code_emit@symbol(): sym=_rcif ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc _rcif___byte, _rcif___bit goto rb2bus_byte_get__2 ; line_number = 129 ; call wait() ;info 129, 605 call wait goto rb2bus_byte_get__1 rb2bus_byte_get__2: ; Recombine size1 = 0 || size2 = 0 ; line_number = 128 ; while !_rcif done ; # Record the 9th bit in {address_bit}: ; line_number = 132 ; address_bit := _false ;info 132, 607 bcf rb2bus_byte_get__address_bit___byte, rb2bus_byte_get__address_bit___bit ; line_number = 133 ; if _rx9d start ;info 133, 608 ; =>bit_code_emit@symbol(): sym=_rx9d ; 1TEST: Single test with code in skip slot btfsc _rx9d___byte, _rx9d___bit ; line_number = 134 ; address_bit := _true ;info 134, 609 bsf rb2bus_byte_get__address_bit___byte, rb2bus_byte_get__address_bit___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 133 ; if _rx9d done ; line_number = 135 ; value := _rcreg ;info 135, 610 movf _rcreg,w movwf rb2bus_byte_get__value ; # Clear any errors by toggling _{cren}: ; # FIXME: All of this should be done *before* reading {_rcreg}!!! ; line_number = 139 ; if _oerr start ;info 139, 612 ; =>bit_code_emit@symbol(): sym=_oerr ; 1TEST: Single test with code in skip slot btfsc _oerr___byte, _oerr___bit ; line_number = 140 ; _cren := _false ;info 140, 613 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 139 ; if _oerr done ; line_number = 141 ; if _ferr start ;info 141, 614 ; =>bit_code_emit@symbol(): sym=_ferr ; 1TEST: Single test with code in skip slot btfsc _ferr___byte, _ferr___bit ; line_number = 142 ; _cren := _false ;info 142, 615 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 141 ; if _ferr done ; line_number = 143 ; _cren := _true ;info 143, 616 bsf _cren___byte, _cren___bit ; line_number = 145 ; if address_bit start ;info 145, 617 ; =>bit_code_emit@symbol(): sym=rb2bus_byte_get__address_bit ; No 1TEST: true.size=13 false.size=0 ; No 2TEST: true.size=13 false.size=0 ; 1GOTO: Single test with GOTO btfss rb2bus_byte_get__address_bit___byte, rb2bus_byte_get__address_bit___bit goto rb2bus_byte_get__5 ; # We have an unexpected address select coming in: ; line_number = 147 ; if value = rb2bus_address start ;info 147, 619 ; Left minus Right movf rb2bus_address,w subwf rb2bus_byte_get__value,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=4 false.size=2 ; No 2TEST: true.size=4 false.size=2 ; 2GOTO: Single test with two GOTO's btfss __z___byte, __z___bit goto rb2bus_byte_get__3 ; # We are being selected again: ; line_number = 149 ; rb2bus_selected := _true ;info 149, 623 bsf rb2bus_selected___byte, rb2bus_selected___bit ; line_number = 150 ; _adden := _false ;info 150, 624 bcf _adden___byte, _adden___bit ; line_number = 152 ; call rb2bus_byte_put(rb2_ok) ;info 152, 625 movlw 165 call rb2bus_byte_put ; Recombine code1_bit_states != code2_bit_states goto rb2bus_byte_get__4 ; 2GOTO: Starting code 2 rb2bus_byte_get__3: ; # Somebody else is being selected; we deselect: ; line_number = 155 ; rb2bus_selected := _false ;info 155, 628 bcf rb2bus_selected___byte, rb2bus_selected___bit ; line_number = 156 ; _adden := _true ;info 156, 629 bsf _adden___byte, _adden___bit rb2bus_byte_get__4: ; 2GOTO: code1 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code2 final bitstates:(data:00=uu=>00 code:XX=cc=>XX) ; 2GOTO: code final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 147 ; if value = rb2bus_address done ; # We want to get back to the beginning of decode: ; line_number = 159 ; rb2bus_error := _true ;info 159, 630 bsf rb2bus_error___byte, rb2bus_error___bit ; line_number = 160 ; value := 0 ;info 160, 631 clrf rb2bus_byte_get__value ; Recombine size1 = 0 || size2 = 0 rb2bus_byte_get__5: ; line_number = 145 ; if address_bit done ; # Regular data byte: ; line_number = 163 ; return value start ; line_number = 163 ;info 163, 632 movf rb2bus_byte_get__value,w return ; line_number = 163 ; return value done ; delay after procedure statements=non-uniform ; line_number = 166 ;info 166, 634 ; procedure rb2bus_byte_put rb2bus_byte_put: ; Last argument is sitting in W; save into argument variable movwf rb2bus_byte_put__value ; delay=4294967295 ; line_number = 167 ; argument value byte rb2bus_byte_put__value equ globals___0+4 ; line_number = 168 ; returns_nothing ; # This procedure will send {value} to the bus. It automatically ; # consumes the echo that is on the bus. If {rb2bus_error} is ; # set, this procedure does nothing. ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 174 ; if !rb2bus_error start ;info 174, 635 ; =>bit_code_emit@symbol(): sym=rb2bus_error ; No 1TEST: true.size=0 false.size=16 ; No 2TEST: true.size=0 false.size=16 ; 1GOTO: Single test with GOTO btfsc rb2bus_error___byte, rb2bus_error___bit goto rb2bus_byte_put__4 ; # Wait until {_txreg} is ready for a value: ; line_number = 176 ; while !_txif start rb2bus_byte_put__1: ;info 176, 637 ; =>bit_code_emit@symbol(): sym=_txif ; No 1TEST: true.size=0 false.size=2 ; No 2TEST: true.size=0 false.size=2 ; 1GOTO: Single test with GOTO btfsc _txif___byte, _txif___bit goto rb2bus_byte_put__2 ; line_number = 177 ; call wait() ;info 177, 639 call wait goto rb2bus_byte_put__1 rb2bus_byte_put__2: ; Recombine size1 = 0 || size2 = 0 ; line_number = 176 ; while !_txif done ; # Ship {value} out to the bus with 9th bit turned off: ; line_number = 180 ; _adden := _false ;info 180, 641 bcf _adden___byte, _adden___bit ; line_number = 181 ; _tx9d := _false ;info 181, 642 bcf _tx9d___byte, _tx9d___bit ; line_number = 182 ; _txreg := value ;info 182, 643 movf rb2bus_byte_put__value,w movwf _txreg ; # Wait for the echo to show up: ; line_number = 185 ; while !_rcif start rb2bus_byte_put__3: ;info 185, 645 ; =>bit_code_emit@symbol(): sym=_rcif ; 1TEST: Single test with code in skip slot btfss _rcif___byte, _rcif___bit ; # Still waiting: goto rb2bus_byte_put__3 ; Recombine size1 = 0 || size2 = 0 ; line_number = 185 ; while !_rcif done ; # Throw the received byte away (store into {_w}). ; line_number = 188 ; assemble ;info 188, 647 ; line_number = 189 ;info 189, 647 movf _rcreg,w ; # Recover from any receive errors by toggling {_cren}: ; line_number = 192 ; if _oerr start ;info 192, 648 ; =>bit_code_emit@symbol(): sym=_oerr ; 1TEST: Single test with code in skip slot btfsc _oerr___byte, _oerr___bit ; line_number = 193 ; _cren := _false ;info 193, 649 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 192 ; if _oerr done ; line_number = 194 ; if _ferr start ;info 194, 650 ; =>bit_code_emit@symbol(): sym=_ferr ; 1TEST: Single test with code in skip slot btfsc _ferr___byte, _ferr___bit ; line_number = 195 ; _cren := _false ;info 195, 651 bcf _cren___byte, _cren___bit ; Recombine size1 = 0 || size2 = 0 ; line_number = 194 ; if _ferr done ; line_number = 196 ; _cren := _true ;info 196, 652 bsf _cren___byte, _cren___bit rb2bus_byte_put__4: ; Recombine size1 = 0 || size2 = 0 ; line_number = 174 ; if !rb2bus_error done ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 199 ;info 199, 654 ; procedure rb2bus_command rb2bus_command: ; Last argument is sitting in W; save into argument variable movwf rb2bus_command__command ; delay=4294967295 ; line_number = 200 ; argument command byte rb2bus_command__command equ globals___0+7 ; line_number = 201 ; returns_nothing ; # This procedure will process an shared {command}. This procedure ; # accesses the global string {id}. ; line_number = 206 ; local new_address byte rb2bus_command__new_address equ globals___0+5 ; line_number = 207 ; local temp byte rb2bus_command__temp equ globals___0+6 ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 209 ; switch command & 7 start ;info 209, 655 ; switch_before:(data:00=uu=>00 code:X0=cu=>X0) size=1 movlw rb2bus_command__13>>8 movwf __pclath movlw 7 andwf rb2bus_command__command,w ; switch after expression:(data:00=uu=>00 code:X0=cu=>X0) addlw rb2bus_command__13 movwf __pcl ; page_group 8 rb2bus_command__13: goto rb2bus_command__14 goto rb2bus_command__14 goto rb2bus_command__14 goto rb2bus_command__14 goto rb2bus_command__9 goto rb2bus_command__10 goto rb2bus_command__11 goto rb2bus_command__12 ; line_number = 210 ; case 4 rb2bus_command__9: ; # 1111 1100 (Address_Set): ; # Return old address: ; line_number = 213 ; call rb2bus_byte_put(rb2bus_address) ;info 213, 669 movf rb2bus_address,w call rb2bus_byte_put ; # Fetch new address: ; line_number = 216 ; new_address := rb2bus_byte_get() ;info 216, 671 call rb2bus_byte_get movwf rb2bus_command__new_address ; line_number = 217 ; if new_address = 0 || new_address = rb2bus_address start ;info 217, 673 ; Left minus Right movf rb2bus_command__new_address,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=1 false.size=36 ; No 2TEST: true.size=1 false.size=36 ; 2GOTO: Single test with two GOTO's btfsc __z___byte, __z___bit goto rb2bus_command__5 ; Recombine code1_bit_states != code2_bit_states ; &&||: index=1 true_delay=4294967295 false_delay=4294967295 goto_delay=4294967295 ; Left minus Right movf rb2bus_address,w subwf rb2bus_command__new_address,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=4 false.size=27 ; No 2TEST: true.size=4 false.size=27 ; 2GOTO: Single test with two GOTO's btfss __z___byte, __z___bit goto rb2bus_command__6 rb2bus_command__5: ; line_number = 218 ; call rb2bus_byte_put(0) ;info 218, 680 movlw 0 call rb2bus_byte_put ; line_number = 219 ; rb2bus_error := _true ;info 219, 682 bsf rb2bus_error___byte, rb2bus_error___bit ; line_number = 220 ; rb2bus_selected := _false ;info 220, 683 bcf rb2bus_selected___byte, rb2bus_selected___bit goto rb2bus_command__7 ; 2GOTO: Starting code 2 rb2bus_command__6: ; # Return new address: ; line_number = 223 ; call rb2bus_byte_put(new_address) ;info 223, 685 movf rb2bus_command__new_address,w call rb2bus_byte_put ; # Fetch new address again as a check: ; line_number = 226 ; temp := rb2bus_byte_get() ;info 226, 687 call rb2bus_byte_get movwf rb2bus_command__temp ; line_number = 227 ; if temp != new_address start ;info 227, 689 ; Left minus Right movf rb2bus_command__new_address,w subwf rb2bus_command__temp,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=14 false.size=4 ; No 2TEST: true.size=14 false.size=4 ; 2GOTO: Single test with two GOTO's btfss __z___byte, __z___bit goto rb2bus_command__3 ; line_number = 232 ; call rb2bus_eedata_write(new_address) ;info 232, 693 movf rb2bus_command__new_address,w call rb2bus_eedata_write ; line_number = 233 ; temp := rb2bus_eedata_read() ;info 233, 695 call rb2bus_eedata_read movwf rb2bus_command__temp ; line_number = 234 ; if temp = new_address start ;info 234, 697 ; Left minus Right movf rb2bus_command__new_address,w subwf rb2bus_command__temp,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=3 false.size=1 ; No 2TEST: true.size=3 false.size=1 ; 2GOTO: Single test with two GOTO's btfss __z___byte, __z___bit goto rb2bus_command__1 ; line_number = 235 ; rb2bus_address := new_address ;info 235, 701 movf rb2bus_command__new_address,w movwf rb2bus_address ; line_number = 236 ; call rb2bus_byte_put(rb2_ok) ;info 236, 703 movlw 165 goto rb2bus_command__2 ; 2GOTO: Starting code 2 rb2bus_command__1: ; line_number = 238 ; call rb2bus_byte_put(0) ;info 238, 705 movlw 0 rb2bus_command__2: ; 2GOTO: code1 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code2 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code final bitstates:(data:00=uu=>00 code:X0=cu=>X0) call rb2bus_byte_put ; line_number = 234 ; if temp = new_address done goto rb2bus_command__4 ; 2GOTO: Starting code 2 rb2bus_command__3: ; line_number = 228 ; call rb2bus_byte_put(0) ;info 228, 708 movlw 0 call rb2bus_byte_put ; line_number = 229 ; rb2bus_error := _true ;info 229, 710 bsf rb2bus_error___byte, rb2bus_error___bit ; line_number = 230 ; rb2bus_selected := _false ;info 230, 711 bcf rb2bus_selected___byte, rb2bus_selected___bit rb2bus_command__4: ; 2GOTO: code1 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code2 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 227 ; if temp != new_address done rb2bus_command__7: ; 2GOTO: code1 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code2 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; &&||: index=0 true_delay=4294967295 false_delay=4294967295 goto_delay=4294967295 ; &&||:: index=0 new_delay=4294967295 goto_delay=4294967295 ; 2GOTO: No goto needed; true=rb2bus_command__5 false= true_size=1 false_size=36 ; 2GOTO: code1 final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; 2GOTO: code2 final bitstates:(data:XX=cc=>XX code:X0=cu=>X0) ; 2GOTO: code final bitstates:(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 217 ; if new_address = 0 || new_address = rb2bus_address done goto rb2bus_command__14 ; line_number = 239 ; case 5 rb2bus_command__10: ; # 1111 1101 (Id_next): ; line_number = 241 ; if rb2bus_index < id.size start ;info 241, 713 movlw 20 subwf rb2bus_index,w ; =>bit_code_emit@symbol(): sym=__c ; No 1TEST: true.size=0 false.size=4 ; No 2TEST: true.size=0 false.size=4 ; 1GOTO: Single test with GOTO btfsc __c___byte, __c___bit goto rb2bus_command__8 ; line_number = 242 ; call rb2bus_byte_put(id[rb2bus_index]) ;info 242, 717 movf rb2bus_index,w call id call rb2bus_byte_put ; line_number = 243 ; rb2bus_index := rb2bus_index + 1 ;info 243, 720 incf rb2bus_index,f ; #if rb2bus_index >= id.size ; # rb2bus_index := rb2bus_index - 1 rb2bus_command__8: ; Recombine size1 = 0 || size2 = 0 ; line_number = 241 ; if rb2bus_index < id.size done goto rb2bus_command__14 ; line_number = 246 ; case 6 rb2bus_command__11: ; # 1111 1110 (Id_start): ; line_number = 248 ; rb2bus_index := 0 ;info 248, 722 clrf rb2bus_index goto rb2bus_command__14 ; line_number = 249 ; case 7 rb2bus_command__12: ; # 1111 1111 (Deselect): ; line_number = 251 ; call rb2bus_deselect() ;info 251, 724 call rb2bus_deselect rb2bus_command__14: ; line_number = 209 ; switch command & 7 done ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; buffer = 'rb2bus_pic16f688' ; line_number = 18 ;info 18, 726 ; procedure rb2bus_initialize rb2bus_initialize: ; Last argument is sitting in W; save into argument variable movwf rb2bus_initialize__address ; delay=4294967295 ; line_number = 19 ; argument address byte rb2bus_initialize__address equ globals___0+8 ; line_number = 20 ; returns_nothing ; # This procedure is responsibile for initializing the UART ; # connected to the bus. {address} is the address of this ; # slave module. This code is specific to the PIC16F688. ; # Warm up the UART: ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 27 ; _trisc@5 := _true ;info 27, 727 rb2bus_initialize__select__1___byte equ _trisc rb2bus_initialize__select__1___bit equ 5 bsf __rp0___byte, __rp0___bit bsf rb2bus_initialize__select__1___byte, rb2bus_initialize__select__1___bit ; line_number = 28 ; _trisc@4 := _true ;info 28, 729 rb2bus_initialize__select__2___byte equ _trisc rb2bus_initialize__select__2___bit equ 4 bsf rb2bus_initialize__select__2___byte, rb2bus_initialize__select__2___bit ; # Initialize the {_txsta} register: ; line_number = 31 ; _txsta := 0 ;info 31, 730 bcf __rp0___byte, __rp0___bit clrf _txsta ; line_number = 32 ; _tx9 := _true ;info 32, 732 bsf _tx9___byte, _tx9___bit ; #_tx9 := _false ; line_number = 34 ; _txen := _true ;info 34, 733 bsf _txen___byte, _txen___bit ; line_number = 35 ; _brgh := _true ;info 35, 734 bsf _brgh___byte, _brgh___bit ; # Initialize the {_rcsta} register: ; line_number = 38 ; _rcsta := 0 ;info 38, 735 clrf _rcsta ; line_number = 39 ; _spen := _true ;info 39, 736 bsf _spen___byte, _spen___bit ; line_number = 40 ; _rx9 := _true ;info 40, 737 bsf _rx9___byte, _rx9___bit ; line_number = 41 ; _cren := _true ;info 41, 738 bsf _cren___byte, _cren___bit ; #_adden := _true ; line_number = 43 ; _adden := _false ;info 43, 739 bcf _adden___byte, _adden___bit ; # Set up the baud rate generator: ; line_number = 46 ; _baudctl := 0 ;info 46, 740 clrf _baudctl ; line_number = 47 ; _brg16 := _true ;info 47, 741 bsf _brg16___byte, _brg16___bit ; line_number = 48 ; _spbrg := _eusart_500000_low ;info 48, 742 movlw 9 movwf _spbrg ; line_number = 49 ; _spbrgh := _eusart_500000_high ;info 49, 744 clrf _spbrgh ; line_number = 51 ; rb2bus_selected := _false ;info 51, 745 bcf rb2bus_selected___byte, rb2bus_selected___bit ; line_number = 52 ; rb2bus_error := _false ;info 52, 746 bcf rb2bus_error___byte, rb2bus_error___bit ; line_number = 53 ; rb2bus_index := 0 ;info 53, 747 clrf rb2bus_index ; # Deal with setting {rb2bus_address} from EEData memory: ; line_number = 56 ; rb2bus_address := rb2bus_eedata_read() ;info 56, 748 call rb2bus_eedata_read movwf rb2bus_address ; line_number = 57 ; if rb2bus_address = 0 start ;info 57, 750 ; Left minus Right movf rb2bus_address,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=2 false.size=0 ; No 2TEST: true.size=2 false.size=0 ; 1GOTO: Single test with GOTO btfss __z___byte, __z___bit goto rb2bus_initialize__3 ; # EE data not set, so use {address} passed in as a argument: ; line_number = 59 ; rb2bus_address := address ;info 59, 753 movf rb2bus_initialize__address,w movwf rb2bus_address ; Recombine size1 = 0 || size2 = 0 rb2bus_initialize__3: ; line_number = 57 ; if rb2bus_address = 0 done ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; line_number = 64 ;info 64, 756 ; procedure rb2bus_eedata_read rb2bus_eedata_read: ; arguments_none ; line_number = 66 ; returns byte ; # This procedure will return the address stored in EEData. If ; # there is no data, 0 is returned. ; line_number = 71 ; local temp1 byte rb2bus_eedata_read__temp1 equ globals___0+9 ; line_number = 72 ; local temp2 byte rb2bus_eedata_read__temp2 equ globals___0+10 ; # Read the first byte (the address): ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 75 ; _eecon1 := 0 ;info 75, 756 bsf __rp0___byte, __rp0___bit clrf _eecon1 ; line_number = 76 ; _eeadr := rb2bus_eedata_address ;info 76, 758 movlw 254 movwf _eeadr ; line_number = 77 ; _rd := _true ;info 77, 760 bsf _rd___byte, _rd___bit ; line_number = 78 ; temp1 := _eedat ;info 78, 761 movf _eedat,w bcf __rp0___byte, __rp0___bit movwf rb2bus_eedata_read__temp1 ; # Read the second byte (the 1'z complement) ; line_number = 81 ; _eeadr := _eeadr + 1 ;info 81, 764 bsf __rp0___byte, __rp0___bit incf _eeadr,f ; line_number = 82 ; _rd := _true ;info 82, 766 bsf _rd___byte, _rd___bit ; line_number = 83 ; temp2 := _eedat ;info 83, 767 movf _eedat,w bcf __rp0___byte, __rp0___bit movwf rb2bus_eedata_read__temp2 ; # If they are 1's complement of one another, they are valid: ; line_number = 86 ; if temp1 = (0xff ^ temp2) start ;info 86, 770 ; Left minus Right comf rb2bus_eedata_read__temp2,w subwf rb2bus_eedata_read__temp1,w ; =>bit_code_emit@symbol(): sym=__z ; No 1TEST: true.size=2 false.size=0 ; No 2TEST: true.size=2 false.size=0 ; 1GOTO: Single test with GOTO btfss __z___byte, __z___bit goto rb2bus_eedata_read__1 ; # Return the valid address: ; line_number = 88 ; return temp1 start ; line_number = 88 ;info 88, 774 movf rb2bus_eedata_read__temp1,w return ; line_number = 88 ; return temp1 done ; Recombine size1 = 0 || size2 = 0 rb2bus_eedata_read__1: ; line_number = 86 ; if temp1 = (0xff ^ temp2) done ; # They are not 1's complement, so return 0 as an error: ; line_number = 91 ; return 0 start ; line_number = 91 ;info 91, 776 retlw 0 ; line_number = 91 ; return 0 done ; delay after procedure statements=non-uniform ; line_number = 94 ;info 94, 777 ; procedure rb2bus_eedata_write rb2bus_eedata_write: ; Last argument is sitting in W; save into argument variable movwf rb2bus_eedata_write__address ; delay=4294967295 ; line_number = 95 ; argument address byte rb2bus_eedata_write__address equ globals___0+11 ; line_number = 96 ; returns_nothing ; # This procedure will write {address} into the EEData. The ; # microcontroll pauses while the EEData is written. ; # Clear out the {_eecon1} register ; before procedure statements delay=non-uniform, bit states=(data:00=uu=>00 code:X0=cu=>X0) ; line_number = 102 ; _eecon1 := 0 ;info 102, 778 bsf __rp0___byte, __rp0___bit clrf _eecon1 ; line_number = 103 ; _eeadr := rb2bus_eedata_address ;info 103, 780 movlw 254 movwf _eeadr ; line_number = 104 ; _eedat := address ;info 104, 782 bcf __rp0___byte, __rp0___bit movf rb2bus_eedata_write__address,w bsf __rp0___byte, __rp0___bit movwf _eedat ; # Write 2 bytes ({address} followed by {address}^0xff): ; line_number = 107 ; loop_exactly 2 start ;info 107, 786 rb2bus_eedata_write__1 equ globals___0+68 movlw 2 bcf __rp0___byte, __rp0___bit movwf rb2bus_eedata_write__1 rb2bus_eedata_write__2: ; # Set the data to write: ; # Set up the for the write: ; line_number = 111 ; _wren := _true ;info 111, 789 bsf __rp0___byte, __rp0___bit bsf _wren___byte, _wren___bit ; line_number = 112 ; _gie := _false ;info 112, 791 bcf _gie___byte, _gie___bit ; line_number = 113 ; _eecon2 := 0x55 ;info 113, 792 movlw 85 movwf _eecon2 ; line_number = 114 ; _eecon2 := 0xaa ;info 114, 794 movlw 170 movwf _eecon2 ; # Start the write: ; line_number = 116 ; _wr := _true ;info 116, 796 bsf _wr___byte, _wr___bit ; # Wait for write to complete: ; line_number = 119 ; while _wr start rb2bus_eedata_write__3: ;info 119, 797 ; =>bit_code_emit@symbol(): sym=_wr ; 1TEST: Single test with code in skip slot btfsc _wr___byte, _wr___bit ; line_number = 120 ; do_nothing ;info 120, 798 goto rb2bus_eedata_write__3 ; Recombine size1 = 0 || size2 = 0 ; line_number = 119 ; while _wr done ; # Disable writing: ; line_number = 123 ; _wren := _false ;info 123, 799 bcf _wren___byte, _wren___bit ; # Prepare the second byte of data: ; line_number = 126 ; _eeadr := _eeadr + 1 ;info 126, 800 incf _eeadr,f ; line_number = 127 ; _eedat := address ^ 0xff ;info 127, 801 bcf __rp0___byte, __rp0___bit comf rb2bus_eedata_write__address,w bsf __rp0___byte, __rp0___bit movwf _eedat bcf __rp0___byte, __rp0___bit ; line_number = 107 ; loop_exactly 2 wrap-up decfsz rb2bus_eedata_write__1,f goto rb2bus_eedata_write__2 ; line_number = 107 ; loop_exactly 2 done ; delay after procedure statements=non-uniform ; Implied return retlw 0 ; Code bank 1; Start address: 2048; End address: 4095 org 2048 ; Configuration bits ; address = 0x2007, fill = 0x3000 ; fcmen = off (0x0) ; ieso = off (0x0) ; boden = off (0x0) ; cpd = off (0x80) ; cp = off (0x40) ; mclre = off (0x0) ; pwrte = off (0x10) ; wdte = off (0x0) ; fosc = ec (0x3) ; 12499 = 0x30d3 __config 12499 ; Define start addresses for data regions ; Region="shared___globals" Address=112" Size=16 Bytes=0 Bits=0 Available=16 ; Region="globals___0" Address=32" Size=80 Bytes=69 Bits=5 Available=10 ; Region="globals___1" Address=160" Size=80 Bytes=0 Bits=0 Available=80 ; Region="globals___2" Address=288" Size=80 Bytes=0 Bits=0 Available=80 ; Region="shared___globals" Address=112" Size=16 Bytes=0 Bits=0 Available=16 end